User manual CASIO EXILIM EX-FC100

[. . . ] E Digital Camera User's Guide Thank you for purchasing this CASIO product. · Before using it, be sure to read the precautions contained in this User's Guide. · Keep the User's Guide in a safe place for future reference. · For the most up-to-date information about this product, visit the official EXILIM Website at http://www. exilim. com/ Unpacking As you unpack your camera, check to make sure that all items shown below are included. [. . . ] Failure to insert the connector fully can result in poor communication or malfunction. · Note that even while the connector is fully inserted, you still will be able to see the metal part of the connector as shown in the illustration. · Make sure that the camera is turned off before plugging in or unplugging the cable. Check the user documentation that comes with the TV for information about requirements before plugging into or unplugging from the TV. 2. Turn on the TV and select its video input mode. If the TV has more than one video input, select the one where the camera is connected. 106 Viewing Snapshots and Movies 3. Press [p] (PLAY) to turn on the camera. This will cause an image to appear on the TV screen, without anything appearing on the camera's monitor screen. · Pressing [ON/OFF] or [r] (REC) will not turn on the camera while the AV cable is connected. · You also can change the aspect ratio of the screen and the video output system (page 157). 4. Now you can display images and play back movies as you normally do. IMPORTANT! · Before connecting to a TV to display images, be sure to configure the camera's [r] (REC) and [p] (PLAY) buttons for "Power On" or "Power On/Off" (page 156). · Audio is initially output by the camera at maximum volume. When you first start displaying images, set the TV volume control at a relatively low level and then adjust it as required. NOTE · Audio is monaural. · Some TVs may not be able to output images and/or audio correctly. · All icons and indicators that appear on the monitor screen also appear on the TV screen. You can use [8] (DISP) to change the display contents. Recording Camera Images to a DVD Recorder or Video Deck Use the following method to connect the camera to the recording device using the camera's bundled AV cable. ­ DVD recorder or video deck: Connect the AV cable to the VIDEO IN and AUDIO IN terminals. ­ Camera: Connect the AV cable to the USB/AV port You can play a slideshow of snapshots and movies on the camera and record it on a DVD or video tape. You can record movies by selecting "» Only" for the slideshow "Images" setting (page 108). When recording images to an external device, use [8] (DISP) to clear all indicators from the monitor screen (page 159). For information about connecting a monitor to the recording device and about how to record, see the user documentation that comes with the recording device you are using. 107 Viewing Snapshots and Movies Other Playback Functions (PLAY) This section explains menu items that you can use to configure settings and perform other playback operations. For information about menu operations, see page 80. Playing a Slideshow on the Camera (Slideshow) Procedure [p] (PLAY) * [MENU] * PLAY Tab * Slideshow Start Starts the slideshow Images Specifies the type of images to be included in the slideshow All images: Snapshots, movies, continuous shutter images All images except Z: All non-continuous shutter (CS) images T Only: Snapshots only » Only: Movies only One Image: One single selected image (selected using [4] and [6]) Time Time from the start to the end of the slideshow 1 to 5 minutes, 10 minutes, 15 minutes, 30 minutes, 60 minutes Interval Amount of time each image remains displayed Use [4] and [6] to select a value from 1 to 30 seconds, or "MAX". If you specify a value from 1 to 30 seconds, movies play from beginning to end. When the slideshow reaches a movie file while "MAX" is selected, only the first frame of the movie will displayed. 108 Other Playback Functions (PLAY) Effect Select the effect you want. Pattern 1 to 5: Plays background music and applies an image change effect. · Patterns 2 through 4 have different background music, but they all use the same image change effect. · Pattern 5 can be used for playback of snapshots only (except for those that are part of a CS group), and the "Interval" setting is ignored. [. . . ] Actual values depend on the type of image being shot. · The above values are based on use of a PRO HIGH SPEED SD memory card (Panasonic Corporation). The number of images you can save depends on the type of memory card you are using. · When using a memory card with a different capacity, calculate the number of images as a percentage of 1GB. [. . . ]