User manual CASIO EXILIM EX-FH20

[. . . ] E Digital Camera User's Guide K1160PCM2DMX Thank you for purchasing this CASIO product. · Before using it, be sure to read the precautions contained in this User's Guide. · Keep the User's Guide in a safe place for future reference. · For the most up-to-date information about this product, visit the official EXILIM Website at http://www. exilim. com/ Unpacking As you unpack your camera, check to make sure that all items shown below are included. [. . . ] Use [8] and [2] to select "Copy", and then press [SET]. NOTE · The functions below cannot be performed on snapshots inside a CS group folder. Before using either of these functions, perform the above procedure (Select Frame) to copy the image first. Cropping, Rotation, Resize 91 Viewing Snapshots and Movies Zooming an On-screen Image 1. 2. In the PLAY mode, use [4] and [6] to scroll through the images until the one you want is displayed. Slide the zoom controller towards z ([) to zoom. You can use [8], [2], [4], and [6] to scroll the zoomed image on the monitor screen. Slide the zoom controller towards w to unzoom the image. ­ When monitor screen contents are turned on, a graphic in the lower right corner of the screen shows what part of the zoomed image is currently displayed. ­ To exit the zoom screen, press [MENU]. ­ Though the maximum image zoom factor is 8X, certain image sizes may not allow zooming up to the full 8X. Zoom factor Image area Current display area Displaying the Image Menu 1. In the PLAY Mode, slide the zoom controller towards w (]). Use [8], [2], [4] and [6] to move the selection boundary around the image menu. To view a particular image, use [8], [2], [4], or [6] to move the selection boundary to the image you want and then press [SET]. · In the case of a movie or a continuous shutter (CS) file, the first frame of the file will be displayed. Boundary 92 Viewing Snapshots and Movies Viewing Snapshots and Movies on a TV Screen 1. Use the AV cable that comes with the camera to connect it to the TV. AV cable (bundled) USB/AV port TV Video Audio Yellow White AUDIO IN jack (white) VIDEO IN jack (yellow) Making sure that the 6 mark on the camera is aligned with the 4 mark of the AV cable connector, connect the cable to the camera. · Make sure that you insert the cable connector into the USB/AV port until you feel it click securely into place. Failure to insert the connector fully can result in poor communication or malfunction. · Note that even while the connector is fully inserted, you still will be able to see the metal part of the connector as shown in the illustration. · Before connecting to a TV to display images, be sure to configure the camera's [r] (REC) and [p] (PLAY) buttons for "Power On" or "Power On/Off" (page 132). · Make sure that the camera is turned off before plugging in or unplugging the cable. Check the user documentation that comes with the TV for information about requirements before plugging into or unplugging from the TV. 2. Turn on the TV and select its video input mode. If the TV has more than one video input, select the one where the camera is connected. 93 Viewing Snapshots and Movies 3. Press [p] (PLAY) to turn on the camera. This will cause an image to appear on the TV screen, without anything appearing on the camera's monitor screen. · Pressing [ON/OFF] or [r] (REC) will not turn on the camera while the AV cable is connected. · You also can change the aspect ratio of the screen and the video output system (page 133). 4. Now you can display images and play back movies as you normally do. Recording Camera Images to a DVD Recorder or Video Deck Use one of the following methods to connect the camera to the recording device using the camera's bundled AV cable. ­ DVD recorder or video deck: Connect to the VIDEO IN and AUDIO IN terminals. ­ Camera: USB/AV port You can play a slideshow of snapshots and movies on the camera and record it on a DVD or video tape. You can record movies by selecting "» Only" for the slideshow "Images" setting (page 95). When recording images to an external device, use [DISP] to clear all indicators from the monitor screen (page 136). [. . . ] Actual capacity depends on image contents. · File size and data rate values are approximate and intended for reference only. Actual values depend on the type of image being shot. · The above values are based on use of a PRO HIGH SPEED SD memory card (Panasonic Corporation). [. . . ]