User manual CASIO YA-P10

[. . . ] $ A triangle indicates a situation against which you need to exercise caution. The example shown here indicates you should take precaution against electric shock. A circle with a line through it indicates information about an action that you should not perform. The specific action is indicated by the figure inside the circle. [. . . ] Failure to do so creates the risk of battery overheating, fire, and explosion. Fluid leaking from a battery that gets onto your skin or clothing can cause skin irritation. If this happens, immediately rinse the area with clean water. E-11 Important! Connecting the pointer to a computer for charging, make sure that the computer is connected to an AC power source to ensure a stable power supply. If your computer does not supply power via its USB port when turned off, leave your computer turned on while charging the pointer. The pointer cannot be used while it is being charged. Installing the Software that Comes with the Pointer on a Computer See the Presentation Draw User's Guide on the CD-ROM that comes with the pointer. E-12 Connecting a Computer to the Projector In order to use the pointer as a computer pointing device, there must be a USB connection between the computer and the projector. To project the computer screen contents with the projector, you also need to connect the analog RGB output terminal of the computer to the projector's COMPUTER IN terminal. Connect as shown in the illustration below. <Projector> COMPUTER IN terminal (1 or 2*) <Computer> Mini D-Sub cable that comes with projector To monitor terminal (analog RGB output terminal) AUDIO IN terminal (1 or 2*) USB-B port To USB port To line output terminal USB cable (Type A to Type B) that comes with pointer Audio cable (commercially available) * Some models have only one COMPUTER IN and one AUDIO IN terminal. E-13 Important! After connection is complete, be sure to change the projector's "Option Settings 2 Interactive Pointer" setting to "On". For more information, see the User's Guide on the CD-ROM that comes with the projector. Be sure to make the RGB output of the computer connected to the projector the primary monitor. The pointer will not operate properly if it is the secondary monitor. For information about configuring monitor settings, see the user documentation that came with your computer, computer help, etc. E-14 Using the Pointer Holding the Pointer Hold the pointer securely as shown in the illustrations below. or E-15 To start a pointer operation 1. Press the pointer left mouse button or 2. right mouse button. · This turns on the pointer and causes the link indicator to start flashing. Holding the pointer securely, point the pointer tip at the projected image. · The link indicator will go from flashing to lit when a link between the pointer and projector is established. Powering down* Battery is charging or battery power is low (approximately 20% of full charge). Very low battery power (approximately 10 % of full charge) : Battery indicator (red) : Link indicator (blue) : Lit : Flashing : Unlit * The pointer will turn off automatically and both indicators will go out if no pointer operation is performed for a few minutes or if a few minutes elapse after the link between the pointer and projector is broken. A few seconds immediately before this happens, the link indicator will flash and then both indicators will light. Pointer Status E-18 Troubleshooting Check the following items whenever you experience any problem while using the pointer. Problem Possible cause and recommended action If the pointer's battery indicator is flashing or light, it means that the pointer battery level is low. See "Charging the Pointer" (page E-11). There may be a problem with the USB connection between the computer and projector. See "Connecting a Computer to the Projector" (page E-13). "Off" may be selected for the projector's "Option Settings 2 Interactive Pointer" setting. For more information, see the User's Guide on the CD-ROM that comes with the projector. Lighting in the location where you are projecting may be too bright. [. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For Users in Canada These Class B digital apparatuses comply with Canadian ICES-003. Cet appareil numériqué de la classes B est conformé à la norme NMB-003 du Canada. These devices comply with RSS 210 of Industry Canada (IC). Operation is subject to the following two conditions: (1) These devices may not cause interference, and (2) These devices must accept any interference, including interference that may cause undesired operation of this device. [. . . ]