User manual CAT EYE CC-7000 VECTRA

[. . . ] In addition to functions for the bicycling activity, it can be used on its own as an independent altimeter for mountain climbing. The features are as follows: Altimeter Functions: · Measures current altitude (above sea level), trip altitude gain, total altitude gain in a temperaturecompensated 1 meter resolution. · Measures atmospheric temperature. · Can reset trip altitude gain alone. [. . . ] Press this button when setting up the unit for bicycle for the first time, or when irregular display occurs. After pressing this AC button, all displays illuminate and then only the "km/h" symbol appears. The accumulated data (total distance and total altitude gain) and the stored wheel circumference are not deleted by this operation. After this operation, only the speed scale, temperature scale and clock time must be set again, according to "Main Unit Preparation" (refer to page 7). 8 Reset When the S/S button and the Mode button are pressed simultaneously, the following data can be reset, depending on the mode. For resetting trip distance(D), elapsed time(T), average speed(A) and maximum speed (M): In other modes than altitude measuring mode, press the two buttons simultaneously; then the data of D, T, A and M returns to zero. E For resetting the trip altitude gain: In the sub mode showing the trip altitude gain and total altitude gain, press the two buttons simultaneously; then the data of the trip altitude gain( ) returns to zero. For resetting the current altitude correction value: In the main mode showing the current altitude ( ), press the two buttons simultaneously; then the current altitude correction value will be zero and the data will be reset to the initial value of "International Standard Atmosphere" (ISO 2533). HOW TO USE AS AN ALTIMETER Correlation between above sea level and pressure extract from ISO 2533 (Table 1) A. S. Level Pres. In seemingly stable weather conditions, you may expect to see the Altitude fluctuate as much as 100 feet from morning to evening because of the warming aspects of the sun on the atmosphere. Symbol on Skipped pressure change Neglecting pressure change Stopped Lapse of time Pressure change Altitude Riding Fig. 11 Riding 2. 10) When using this unit on bicycle, switch on the bicycle symbol. In this way, the change of the pressure will have an influence on the altitude data only when the unit perceives the speed signal, regardless of start/stop. Thus, the altitude data will not be affected even if pressure changes occur while bicycle is stopped. Note: If the pressure changes while riding, the altitude data will give an error. Continuous Measuring Mode (Bicycle Symbol: off) When using this unit on its own apart from a bicycle, for hiking etc. , switch off the bicycle symbol. In this way, the altitude data is always influenced by the change of the pressure (Fig. Align the magnet's center and the sensor's marking line (Fig. 18), and clearance between the magnet and the sensor should be 2mm (Fig. Cut off the excess of the sensor band B. Note: If the space between the fork and the spokes are too narrow, mount the sensor without the holster. Magnet Spoke Rubber Pad Parallel Sensor Band A Fig. 14 Fig. 15 Fig. 16 Speed Sensor Sensor Band B Marking Line of Sensor Magnet Speed Sensor Center of the Magnet Front Fork Sensor Holster Fig. 17 Fig. 18 About 2 mm Fig. 19 11 Bracket Bracket E Wire Rubber Pad Fig. 21 Wire Securing Tape Slide Speed Sensor Fig. 20 Front Fig. 22 Lever · Secure the wire with the wire securing tape as in Fig. Wind the wire round the outer cable up to the handlebar. When adjusting the length, be careful that the wire will not hinder handlebar operation. · By using the rubber pad, attach the bracket close to the handlebar stem (Fig. 21). Mounting Main Unit Slide the main unit onto the bracket from front until it clicks into position. The contacts will automatically connect. To remove the unit, pull it off forward while pushing down the lever (Fig. Spin the wheel to check if the display shows the speed. [. . . ] In the Auto function, this button doesn't work. When using the unit apart from bicycle, it doesn't measure altitude. Clear off the bicycle symbol, and turn to the continuous measuring mode. Is there anything clogged in the altitude sensor cover? [. . . ]