User manual CAT EYE CC-MT200

[. . . ] Setting Values Cross Reference Table (The tire size is marked on both sides of the tire. ) Table de Correspondance des Valeurs de Réglage (La dimension du pneu figure de chaque côté du pneu) Wertetabelle zur Einstellung des Radumfanges (die Radgröße entnehmen Sie der Aufschrift des Reifens) Tabel voor het bepalen van de wielomtrek (de bandenmaat staat vermeld aan beide zijden van de band) CYCLOCOMPUTER Model CC-MT200 Tabella delle Corrispondenze dei Valori di Regolazione (La dimensione del pneumatico figura su ogni lato del pneumatico) Tabla de Valores (El tamaño de la rueda está marcado al lado de la llanta) TIRE SIZE dimension du pneu Radgröße bandenmaat dimensione del pneumatico Tamaño de rueda L(cm) TIRE SIZE dimension du pneu Radgröße bandenmaat dimensione del pneumatico Tamaño de rueda L(cm) TIRE SIZE dimension du pneu Radgröße bandenmaat dimensione del pneumatico Tamaño de rueda L(cm) 20 x 1. 75 24 x 1 U. S. 4636769/4642606/5236759/5226340 and Design Patented Copyright© 1995 CATEYE Co. , Ltd. CCMMT2-981120 Printed in Japan 0687350 150 175 178 179 191 189 192 196 191 195 195 197 207 210 26 x 1. 40 26 x 1. 50 26 x 1. 75 26 x 1. 95 26 x 2. 00 26 x 2. 1 26 x 2. 125 26 x 2. 35 27 x 1 27 x 1-1/8 27 x 1-1/4 27 x 1-3/8 650 x 35A 650 x 38A 200 199 202 205 206 207 207 208 215 216 216 217 209 212 650 x 38B 700 x 18C 700 x 19C 700 x 20C 700 x 23C 700 x 25C 700 x 28C 700 x 30C 700 x 32C 700C Tubular 700 x 35C 700 x 38C 700 x 44C 211 207 209 209 210 211 214 217 216 213 217 218 222 24 x 3/4 Tubular 24 x 1-1/8 Tubular 24 x 1-1/4 24 x 1. 75 24 x 2. 00 24 x 2. 125 26 x 1(559mm) 26 x 1(650c) 26 x 1. 25 26 x 1-1/8 Tubular 26 x 1-3/8 26 x 1-1/2 7 LIMITED WARRANTY 1-Year Warranty for Main Unit Only (Accessories/Attachments and Battery Consumption excluded) If trouble occurs during normal use, the part of the Main Unit will be repaired or replaced free of charge. The service must be performed by Cat Eye Co. , Ltd. [. . . ] With Reset operation, it returns to zero. AVS Average Speed 0. 0 - 65. 0mile/h ±0. 3 mile/h The average speed from start to current point is displayed within 27 hours 46 minutes 39 seconds (99, 999 seconds) or 999. 99 miles (km). If either is exceeded, (. E) is displayed and calculation ceases. MXS Maximum Speed 0. 0(3. 0) - 65 mile/h(27inch) ±1 mile/h With Reset operation, it returns to zero and counting begins anew. 12-hour clock time The current time is displayed by a 12-hour clock. 0:00' - 11:59' ±0. 003 % · S/S button Starts and stops the measurement of trip distance and elapsed time. During operation, speed scale symbol flashes. In Auto Function, this button is invalid. ODO RESET · SET Button Fig. 2 ALL CLEAR Fig. 3 This is for setting the wheel circumference and clock time, switching on/ off Auto Function and to clear all present data and any irregularity. When pressed in stop state in each mode, the following can be revised. Then mile/h alone will be displayed as illustrated in fig. 5. Km/h and mile/h are alternately displayed with each press of S/S button. Press M button to set desired speed scale. 6. TROUBLE SHOOTING The following situations do not indicate malfunction of the cyclocomputer. Check the following before taking to repair. When current speed does not appear, short-circuit the contact on the back with metal. The unit will function normally if the speed display appears. ----- Is it at a low temperature under 32°F(0°C)?----- It returns to normal state when temperature rises. ----- Has the Lithium Battery in the main unit worn out?----- Replace the Lithium Battery with a new one. ----- Execute "All Clear" operation. ----- Is there anything on the contact of the main unit or of the bracket? [. . . ] For accuracy, set by the radio time signal. screw fork sensor markingline of sensor center of magnet MOUNTING TO BIKE · The spokes must run correctly through the inside the magnet as in sensor fig. 8. magnet · Attach the sensor with Sensor Bands-A-B to the right fork. Choose a band that fits the fork diameter (S size for up to 24ø, L for oversize). Insert the band-B into the slit of the band-A, and put the rubber pad inside of the band-A(fig. [. . . ]