User manual CAT EYE DOUBLE SHOT

[. . . ] · Securely connect the plug so that the cable will not come unplugged or hinder your riding. · Never use damaged components (e. g. , cables, etc. ). Send any damaged components to our customer service department for repair. · The light unit may become extremely hot when on or immediately after it is turned off. [. . . ] Mount the light unit onto the helmet mount. Secure the cable on the rear of the helmet using the spare cable strap. Put on the helmet and adjust the angle of the beam. To remove the light unit, pull the light unit forward while pressing the button on the base of the light unit. CAUTION!: Make sure the light unit is cool to the touch before removing it. H-1 9 1 1. 5 Bracket Strap 6 5 H-2 Connecting the extension cord Connect the extension cord between the light unit and the battery unit. Align the male and female cable ends and connect them. Turn the plugs so that they are securely locked. 23 Precautions when handling the battery unit While riding, place the battery unit in your jersey pocket or hydration/back pack. Before using the light, make sure the battery is correctly stored in its neoprene bag. CAUTION!: Pay attention to the arrangement of the cable so that it does not interfere with the handling of the bicycle. Do not wind the cable because the wire inside the cable may break. 2. 3. NOTE: Wind the fixing strap around the center of the battery unit. Button 9 H-2 Line LOCK HOW TO MOUNT TO A BICYCLE B-1 Installing the bracket/light unit Attach bracket H31 or H32 to the handlebar. NOTE: Select H31 for oversized handlebars. Mount a rubber pad and the bracket onto the handlebar. 2 thicknesses of rubber pads are supplied; if necessary, cut the rubber pad to fit. Tighten and then close the lever to secure it. Make sure the bracket does not rotate on the handlebar. CAUTION!: Be sure to adjust the angle of the light's beam by referring to the "How to Adjust Beam Angle" section in this manual before operating the lighting system. 1 B-1 Handlebar 1. 7 or 8 2. or *H32 9 3. Rubber pad 1 3. To remove unit after use, pull it out while pressing the button on the bracket. CAUTION!: Make sure the light unit is cool to the touch before removing it. Button 23 0 Quick lever B-2 Installing Battery Unit Mount the battery unit on the bicycle frame. Before using the light, make sure the battery is correctly stored in its neoprene bag. CAUTION!: When mounting the unit, make sure that the seam of the battery bag is facing down and the fold line is in front. Wind the fixing strap around the center of the battery unit. B-2 1. Top Tube 2. Fixing Strap Gear & Brake Cables 1. Wrap the fixing strap around the top tube to secure the unit. CAUTION!: Wrap the strap over the top tube but under the gear and brake cables. Wrapping the strap over the cables is dangerous as it may interfere with braking and gear shifting. Fold Line Seam 2. Use the support strap to secure the battery unit to the down tube to prevent it from rolling. NOTE: The battery can also be mounted on alternate positions on the bicycle. However, please make sure that the seam of the battery bag is facing down, and the fold line is in front. This will help prevent any water from entering the bag. Fixing Strap 2, 3 Down Tube 0 B-3 Line B-3 Connecting and Securing Cables Align the male and female cable ends and connect them. [. . . ] Connect the jack to the battery charger. Plug the battery charger to an AC outlet. NOTE: When charging is complete, the indicator light changes from flashing red to green. Charging jack 2 Orange Light Blinking Red Light Green Light : Connected to power source : Charging : Charging is completed Standard charging time Approx. 3 hours Cable Arrangement CAUTION!: When securing the battery to the frame, make sure the fixing strap attaches to the center of the battery unit. The battery unit is stored in its bag as shown in the figure. In case the battery unit is out of its bag, be sure to return it to its original state. [. . . ]