User manual CATEYE ABS-10

[. . . ] ABS-10 is a combination system of a lamp, battery pack and charger. Before operating, thoroughly familiarize yourself with this manual so that you understand the light's safe and correct operation. Please keep this manual, along with the warranty card, for future reference. SAFE OPERATIONS (IMPORTANT) · Never short-circuit the terminal of the battery pack and the plug of the battery charger. It may cause the battery to over heat, resulting in fire or damage of the components. [. . . ] · Overdischarge (leaving the light on after the power is completely gone) shortens the performance life of the battery. · If the lamp body or parts become dirty with mud, etc. , clean with a soft cloth which is moistened with mild soap. Never apply paint thinner, benzine or alcohol; damage will result. CONTENTS The ABS-10 are the combined system of the following parts. Make sure that your package includes all the parts. Battery Belt (L/S) Cable Cover Switch Unit Holder Mounting Bolts (L x 2, S x 2) Holder HOW TO SETUP Bracket (H-32) RECHARGING INSTRUCTIONS Attach the bracket (H-32) to the handlebar. Turn over the quick lever and it is fastened. To remove the lamp body, slide it forward while pushing the lever. Note: Use the quick lever to adjust 10° horizontally. When removing the lamp body, make sure that it has been cooled. Attach the switch unit onto the handlebar where it will not hinder the braking and shifting operation. · Recharge after thorough discharge. (in order to prevent memory after effect) · Use exclusive charger. CLICK! Lever Switch Unit Charge indicator Rubber Pad Quick lever screw CLICK! Velcro CLICK! or Connecting Battery Pack and Cord Choose your favorite location to attach the battery packs. When attaching to bottle cage Attach the holder onto the down tube using the holder mounting bolts (L or S). Holder mounting bolts Holder Battery Pack Attention: Fix the battery pack securely with the hold-down straps. For safety's sake, also use the battery belts (velcro straps) to secure the batteries. · Recharge only when battery power has completely diminished. · Recharged both batteries at the same time. Note: · Red indicator color ---- Empty/Not charged. · Green indicator color - Fully charged. · Battery life will vary due to adverse conditions. Standard Charging Time · Fully charged batteries that yields no power hours means battery life is dead. The home power outlet 8-10 Bulb HOW TO REPLACE THE BULB Disassemble the lamp unit as illustrated. Caution: · Do not rotate the bulb but pull it straight out. Other bulbs will cause the lamp body to melt. · To replace bulb, first let it cool down. [. . . ] After being repaired or replaced, the product will be shipped back to the customer. Address for service: CO. , LTD. 2-8-25 Kuwazu, Higashi Sumiyoshi-ku Osaka 546-0041 JAPAN Attention: CAT EYE International Customer Service Section Service Center for the United States Customers CATEYE Service & Research Center 1705 14th Street #115, Boulder, CO 80302 Phone: 303-443-4595 Fax: 303-473-0006 Toll Free: 800-5CATEYE (800-522-8393) e-mail: service@cateye. com web site: www. cateye. com #533-8880 Bracket (H-32) #533-8790 ABS Battery Pack #533-8795 ABS Jack Packing #533-8671 ABS Holder There is a pad inside of the jack socket to prevent the plug from falling off the socket. When this pad is deteriorated and you feel the plug's connection is loose, replace the pad with a new one. Pad Caution: In this double connection, the two batteries must be evenly discharged. Do not mix batteries that are in different states of charge. #533-8670 ABS Switch Unit HOW TO SWITCH ON/OFF Release Quick release lever #533-8784 ABS Battery Belt The switch unit controls the operation of the lamps. Run Time: 1. 5 hrs Note: The run time shown here is the calculated figure. [. . . ]