User manual CATEYE MSC 2DX

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CATEYE MSC 2DX. We hope that this CATEYE MSC 2DX user guide will be useful to you.

Lastmanuals help download the user guide CATEYE MSC 2DX.


Mode d'emploi CATEYE MSC 2DX
Download
Manual abstract: user guide CATEYE MSC 2DX

Detailed instructions for use are in the User's Guide.

[. . . ] Reference: If the clearance between spoke and front fork is wider than 5mm, mount the sensor band 3 and 4 in an opposite way as shown. front fork Wire Secure the wire along the fork using the nylon ties 5 and wind it round the brake cable up to the handlebar. Caution: Allow enough wire clearance in the area marked with . Bracket Attach the bracket rubber pad with holder 8 to the bracket 1 and mount it to the handle bar. Reference: If it does not fit well, use the rubber pad 7. -3- 2 Chestbelt Heart Rate Sensor Attaching Main Unit and Chest Belt Before Wearing Chestbelt Heart Rate Sensor WARNING!!Pacemaker users should not use this unit. [. . . ] -4- Input the wheel circumference of your bicycle into the main unit. Find out your bicycle's wheel circumference from the table below. If you cannot fine one, use the default figure " 2096" temporarily. Name of Button The tire size is marked on the side of your tire. 3 Setting up Main Unit (1) Initial Setting !-1 Select a Speed Scale wheel circumference The main unit has 6 buttons: SET/AT button, MODE button, LAP button, LT button, S/S button and AC button. -1) Follow the instruction below for the initial setting. Then the entire screen illuminates and gives a beep sound. Push the MODE button to switch between "km/h" and "mph". Push SET/AT button to choose the desired speed scale. Then the wheel symbol appears and the initial figure 2096 flashes. -3) Setting the Wheel Circumference 3. Input your bicycle's wheel circumference obtained from the above table. Push MODE button to increase the digits, and LAP button to decrease. (To increase/decrease rapidly, hold down the respective button. ) Caution: This is just the temporary setting of the wheel circumfer!-3 ence. For more accurate measurement, input the exact wheel circumference. When you want to change wheel circumference later, refer to "Changing wheel circumference" in page 13 of the user manual. Push SET/AT button to fix the setting, and the screen shows "Current Speed " in the upper display, "Heart Rate " in the middle display and "Elapsed Time TM" in the lower display (!Initial setting is completed. "Elapsed Time TM" !-4 -5- (2) Basic Operations Start and stop measurement Push S/S button and the unit will start measuring "Elapsed Time TM". At the same time, calculation of "Trip Distance DST" and "Average Speed AVS" starts. The symbol of bpm in the middle display flashes while measuring. Push S/S button again and the unit stops measuring and calculation. "Current Speed measured and displayed regardless of the start/stop. Switching Functions The upper display always shows "Current Speed ", and the middle display always shows "Heart Rate ". ", "Heart Rate ", "Total Distance ODO", "Maximum Heart Rate MXP" and "Maximum Speed MXS" continue to be In the lower display, the selected function is displayed. [. . . ] Therefore this feature is useful only when riding bicycle. When you use this unit on your wrist as a heart rate monitor, turn off the Auto time feature. Changing Upper Display In the Default State the upper display always shows "Current Speed ". However, you can change it to Clock, by pressing SET/AT button and S/S button simultaneously (in this case "Current speed " comes down to the lower display and joins in the main function). *When Auto function is on, just push S/S button and the upper display changes from "Current speed " to "Clock time ". Reset Operation To reset the data of "Elapsed Time TM", "Average Speed AVS", "Maximum Speed MXS", "Maximum Heart Rate MXP" and "Trip Distance DST", push S/S button and MODE button simultaneously. Pace Arrow When you are using the unit for cycling, the pace arrow appears in the right side of the lower display. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CATEYE MSC 2DX

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CATEYE MSC 2DX will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag