User manual CATEYE TOMO

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CATEYE TOMO. We hope that this CATEYE TOMO user guide will be useful to you.

Lastmanuals help download the user guide CATEYE TOMO.


Mode d'emploi CATEYE TOMO
Download
Manual abstract: user guide CATEYE TOMO

Detailed instructions for use are in the User's Guide.

[. . . ] ----- Execute "All Clear" operation. ----- Is there anything on the contact of the main unit or of the bracket?----- Is the distance between sensor and magnet too far?----- Are the marking line of the sensor and the center of magnet matched each other? [. . . ] *To pull out the band B from band A, tug strongly. Mount the adjusted bands to the fork along with the sensor, by temporarily tightening the screw(fig. Align the magnet's center and the sensor's marking line(fig. 12), and make sure of 2mm clearance between the magnet and sensor (fig. Cut the excess of the band-B with a nipper or the like. · Secure the wire with tape as fig. Wind the wire round the outer cable and adjust length. Loosen the wire in the area marked with the arrow so that the wire does not hinder handlebar operation. · Use either 1mm- or 2 mm-thick pads if necessary, according to handlebar diameter. Attach the bracket close to the handlebar stem (fig. · Slide main unit onto the bracket from front until it clicks into position. To remove, pull it off forward while pushing down the lever. 16) MAIN UNIT PREPARATION The following must be completed before operating. (1) How to measure wheel circumference (L) of your bike (Fig. 4) Put a mark on the tire tread and ride the bike one full wheel revolution. Mark the start and the end of the revolution on the ground and then measure the distance between the two marks. Or, the "Selecting Values Cross Reference Table" tells you an approximate circumference according to tire size. L Fig. 4 (2) Setting Speed Scale Preform all clear operation. Then mile/h alone will be displayed as illustrated in fig. 5. Km/h and mile/h are alternately displayed with each press of S/S button. Press M button to set desired speed scale. 6. Fig. 5 (3) Setting the wheel circumference (Fig. 6) The standard wheel circumference of 216 cm for 27" wheel is displayed. When using 216 cm without revision, press M button. ODO will be displayed and 216 cm is set. [. . . ] In Auto Function, this button is invalid. 12-hour clock time The current time is displayed by a 12-hour clock. 0:00' - 11:59' ±0. 003 % · SET Button This is for setting the wheel circumference and clock time, switching on/off Auto Function and to clear all present data and any irregularity. When pressed in stop state in each mode, the following can be revised. · In ODO mode --------------------- Wheel circumference · In mode ----------------------- 12-hour clock · In TM, DST or AVS mode ----- On/off the Auto function AUTO (AUTOMATIC START/STOP) FUNCTION DST AUTO Reset Operation: (Fig. 2) Select any mode except ODO, then press M button and S/S button simultaneously. (When done in ODO, registered wheel circumference will be displayed. ) RESET All Clear Operation: (Fig. 3) When M button, S/S and set buttons are pressed simultaneously, all data stored (ODO, speed scale, Wheel circumference and clock time) is erased. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CATEYE TOMO

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CATEYE TOMO will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag