User manual CHAMBERLAIN HS670

[. . . ] GL CO NT RO LL ER BO AR D MODEL HS670 HEAVY DUTY HYDRAULIC SLIDE GATE OPERATOR 2 YEAR WARRANTY Serial # ________________________ (located on electrical box cover) Installation Date __________________ MODEL HS670 IS FOR VEHICULAR PASSAGE GATES ONLY AND IS NOT INTENDED FOR PEDESTRIAN PASSAGE GATE USE TABLE OF CONTENTS OPERATOR SPECIFICATIONS Carton Inventory . . 3 Operator Dimensions and Horsepower Chart . . 5 IMPORTANT NOTE · BEFORE attempting to install, operate or maintain the operator, you MUST read and fully understand this manual and follow all safety instructions. · DO NOT attempt repair or service of your commercial door and gate operator unless you are an Authorized Service Technician. OPERATOR WARNINGS Safety Installation Information . [. . . ] NOTE: For single unit applications, a jumper must be placed between TB11 and TB12. In this mode no further communications will take place during travel. If the master detects the presence of a second unit the master will continue to query the second unit during travel. The second unit will send a response to the master for every query. The second operator will stop if there is a period of one second or more of no communications. When two operators are connected in dual gate configuration accessories may be connected to either the master or second. Master or Standalone Gate Setting Master Unit ON Second Gate Setting Master Unit ON S4 Second Unit S4 Second Unit FIGURE 1 TB12 TB11 Shielded Cable (Twisted Pair) Minimum 18 Gauge CONDUIT TB11 TB12 NOTES: · Do not run Master/Second communication wiring in the same conduit as the power and control wiring. · The Second unit will require a normally close stop circuit for proper system operation. · After Master/Second wiring has been completed and the S4 switch programmed, both units must have their power cycled to initiate proper Master/Second communication. · The motor learn function must be completed in stand alone mode prior to Master/Second wiring. STREET Interrupt Loop HS670 (Gate Conduit) 6' Interrupt Loop COMPLEX OR PARKING LOT HS670 18 PROGRAMMING PROGRAMMING THE RADIO RECEIVER SET SECURITY MODE The Universal Receiver can be used with up to 15 rolling code transmitters or passwords in HIGH security mode. Alternately, it can be used with up to 31 of any type transmitter in NORMAL security mode, including any combination of rolling code, billion code, or dip switch remotes. The jumper must be set at the HIGH position for the receiver to operate in HIGH security mode. It must be set at NORMAL position to operate at the NORMAL mode (Figure 1). When changing from NORMAL to HIGH security mode, any previous transmitter codes must be erased. Repeat Steps 2 and 3 in the Programming Section below to reprogram the receiver for each remote control transmitter in use. SET OUTPUT DURATION WARNING To prevent possible SERIOUS INJURY or DEATH from electrocution: · Be sure power is not connected BEFORE installing the receiver. To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: · ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters. · Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. · ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. CAUTION FIGURE 1 Security Mode Terminals Jumper WARNING To prevent possible SERIOUS INJURY or DEATH, the use of CONSTANT OPERATION on residential openers is PROHIBITED. CAUTION AVERTISSEMENT WARNING ATTENTION WARNING Security Mode Terminals Jumper NORMAL SECURITY MODE For commercial applications, the receiver can be set for either constant or momentary closure on the output contacts. Use of constant closure is prohibited on residential garage door openers because it overrides the safety reversal devices. With the jumper in the "M" (Momentary) position, the contacts will close for 1/4 second regardless of the length of radio transmission. [. . . ] For example: HS670-100-21 (Operator) = K-HS670-100-21 (Electrical Box Kit) 3 5 7 8 10 2 15 13 6 12 14 9 1 9 4 11 INDIVIDUAL PARTS AND KITS ITEM PART # 1 K001A5566 2 03-8024-K 3 10-19198 4 10-19199 5 21-3260-1 6 31-13703 7 35-310-032 8 G71-416-7NH 9 42-114-2 10 42-19200 11 42-8116-1 12 74-19201 13 23-3001 23-3005 14 31-G055 15 25-2015 25-2006 DESCRIPTION Control Board Contactor, 3 Pole Reversing Control Box Cover Mounting Bracket Transformer, 50/60HO, 60VA Standoffs for Optional Loop Detector Fuse, Glass Body 3. 2AMP 3AG Loop Detector Terminal Strip, 14 Poles Radio Block 4 Pole Terminal Strip, PCB 16 Pole Control Box Switch 1n Switch 3n Standoffs for GL Board Overload, 15AMP (230V 1PH) Overload, 6AMP (115V 1PH) QTY 1 1 1 1 1 8 1 2 1 1 1 1 1 3 1 NOTES PROVIDED IN KIT Individual Part Individual Part Individual Part Individual Part Individual Part Individual Part Optional Individual Part Individual Part Individual Part Individual Part Complete Assembly Individual Part Individual Part Optional 1PH Units 3PH Units NOTE: Single phase units are equipped with either an external line break device or an internal pilot-duty thermal O/L device. 32 I L L U S T R AT E D PA R T S 9 13 3 5 7 16 4 6 3 2 12 10 14 17 3 10 15 11 1 8 INDIVIDUAL PARTS AND KITS ITEM 1 PART # K20-1100 K20-3100C-4 K20-3200C-4 K32-19007 K32-19008 K75-19103 K75-19102 K75-19101 K75-19100 K75-19099 K75-19098 K75-19097 K75-19096 K75-19095 K75-19094 29-19202 MG49130 K75-19090 K74-G0589 29-19203 80-19011 K75-19104 DESCRIPTION Motor, 1HP 115/230V 1PH Motor, 1HP 230/460V 3PH Motor, 2HP 230/460V 3PH Hydraulic Pump, Class 3&4 Hydraulic Pump, Class 1&2 Tension Rod, 1HP Tension Rod, 2HP Arm, Lower Pivot Arm, Upper Pivot Motor, Hydraulic Guide Assembly Base Assembly Drive Wheel, 1HP Drive Wheel, 2HP Limit Switch Directional Valve Arm Bushings Kit Operator Cover RPM Sensor (Hall Effect) Rectifier (for D. V. ) Traction Ring, H. E. Wheel RPM Assembly QTY 1 NOTES 1HP 1PH Units 1HP 3PH Units 2HP 3PH Units 18 I. P. S. 1HP Units 2HP Units PROVIDED IN KIT Individual Part 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 1 1 1 1 2 1 1 2 1 1 1 1 1 1 1 1 Individual Part Tension Rod, Tension Spring and Mounting Hardware Pivot Arm and Mounting Hardware Pivot Arm and Mounting Hardware Individual Part Guide and Mounting Hardware Base, Mounting Legs and Shield Drive Wheel and Mounting Hardware Limit Switch and Limit Arm Individual Part Mounting Hardware Cover, Handle and Labels Hall Effect Board, Cable and Mounting Hardware Individual Part Individual Part Complete Assembly 1HP Units 2HP Units (2 Required) 33 WARRANTY POLICY LIFTMASTER ® TWO YEAR LIMITED WARRANTY The Chamberlain Group, Inc. warrants to the final purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of two years from the date of purchase. [. . . ]