User manual CHAMBERLAIN LM60K

[. . . ] ⷠRe-connect power supply now and wait. The drive should turn 2x briefly and then run to one of the limit switches as a signal that the command has been understood. As soon as the drive starts turning, the remote controls are deleted. Disconnect link to black cable making sure the free end cannot cause a short circuit. [. . . ] Switch SW2 with the number 1 set to ON = summer time Switch SW2 with the number 1 set to OFF = winter time PROGRAMMING OF UP/DOWN TIMES AUTOMATIC ON / OFF MECHANISM If both buttons on the unit are pressed and held, the following sounds (peeps) are heard in the sequence indicated. 1x peep - automatic mechanism OFF 2x peeps - automatic mechanism ON 3x peeps time programming UP / DOWN possible Please note: If you have held the buttons down for too long, simply repeat the process. Memorising time of day Wait for the time of day at which UP or DOWN is to be programmed. ⷠPress both buttons and wait for 3x peep sounds. From now on, the operation thus memorised (UP or DOWN) will be carried out every 24 hours. ⷠEnd of programming Note 1: Don't forget to set the unit to automatic mode. Note 2: By memorising a new time, the old time is deleted. Note 3:8The automatic mechanism can 5be 6 7 8 deactivated completely to avoid 6 7 9 10 1 2 3 4 any accidental incorrect programming. ⷠSwitch SW2 with the number 2 set to ON = automatic mechanism - deactivated · Switch SW2 with the number 2 set to OFF = automatic mechanism - activated One-off transmission / Three-fold transmission If this option is activated, the wall switch sends the same signal for UP or DOWN to the drive 3x at intervals of 3 321 minutes and 12 seconds. Example: If the first radio signal does not reach the drive, because it has been affected by interference from other radio signals, the second or third attempt is highly likely to reach the drive. A small jumper JP1 is located in the middle of the switch controller. However, the drive must have halted beforehand. Note 3: Don't press a new button before the LED on the remote control has gone out and the drive has stopped moving. Should the drive run in one direction for a long time rather than a short time (between Step 2 and Step 3), the process hasn't worked. PROGRAMMING THE FIRST REMOTE CONTROL (also wall switch) REVERSING DIRECTION OF MOVEMENT The first remote control is the "master" remote control. It also determines the direction of movement and decides whether the upper button is actually responsible for UP functionality or the opposite. Even if all that needs to be programmed is a reversal of direction of movement, all remote controls that have been programmed must still be deleted first (see Deleting with and without remote control). NOTE 1: If the reason for reprogramming was that the buttons on the remote control worked the wrong way round (DOWN/UP), press the DOWN button in the following (only applies to new drives with default programming). NOTE 2: It is recommended to previously program aremote control (such as RA4330 or RA4336) as "master" instead of a wall switch. Press and hold UP button or DOWN button (direction of movement) on the new "master" remote control (stay within radio range of drive) · Re-connect power supply and wait · If it has worked, the drive turns 2x briefly as a signal that the command has been understood. If the process doesn't work, it could perhaps be that a "master" remote control has already been programmed. Should this not be identifiable however, everything will first have to be deleted via "Deletion without remote control". [. . . ] Was the period between the connection of the power supply and pressing the button on the remote control longer than 20 seconds?AUTOMATIC FUNCTION SETTING FOR WINTER TIME / SUMMER TIME (SW2) On the day of programming, switch SW2 marked with the number 1 and located on the inside of the wall switch is set to the right position. Subsequently when in normal operation, the time can altered by 1 hour without the UP/DOWN times needing to be reprogrammed. 1-fold transmission - JP1 between 1 and 2 3-fold transmission - JP1 between 2 and 3 Please note: The 3-fold transmission option can be a hindrance. [. . . ]