User manual CHAMBERLAIN MOTORLIFT ML500 GARAGE DOOR OPERATOR

[. . . ] TM TM Illustrated Instruction Manual for ML500 Garage Door Operator G IN LL RO 43 DE CO de Mo l8 E 35 ML Chamberlain Australia Pty Ltd PO Box 1446 Lane Cove NSW 1595 www. motorlift. com. au Chamberlain New Zealand Ltd P. O. Box 100-221 Auckland 1330 www. motorlift. co. nz 2 WARNING: If your garage has no service entrance door, Model 1702AML Outside Quick Release must be installed. This accessory allows manual operation of the garage door from outside in case of power failure. Sticking or binding doors must be repaired. [. . . ] SAVE THESE INSTRUCTIONS Test the Safety Reverse System 1 Install Protector SystemTM(Optional) ­ (See accessories) After opener has been installed and adjusted, The Protector SystemTM accessory can be installed. Instructions are included with this optional device. The Protector SystemTM provides an additional measure of safety against a small child being caught under a garage door. It uses an invisible beam which, when broken by an obstruction, causes a closing door to open and prevents an open door from closing and is strongly recommended for homeowners with young children. 20 1. Program Remotes 1 2 2 1 3. 2. Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Your garage door opener receiver and Remote Control Transmitter are set to a matching code. If you purchase additional Remote Controls, the garage door opener must be programmed to accept the new Remote code. To program receiver to match additional Remote Control codes: 1. Press and release the program button on the side of the unit (1). The green LED will glow steadily for 30 seconds. 2. Within 30 seconds press and hold the button on the hand-held Remote (2). 3. Release the button when the motor unit light blinks. If the light bulb is not installed, two clicks will be heard. To erase all codes from motor unit memory or to deactivate any unwanted Remote, first erase all codes: Press and hold the program button (1) on motor unit until the learn indicator light goes out (approximately 6 seconds). Reprogram each Remote or Keyless Entry you wish to use. 11 21 2 1 RED 1 WHT 2 12 4 3 4 K LOC 7 22 Replace Light Bulb Locate any Wall Mounted Door Control where the garage door is visible, away from door and door hardware, at a minimum height of 1. 5m. fasten the child warning label on the wall near the Door Control. There are 2 screw terminals (1) on the back of the Door Control (2). Strip about 6mm of insulation from bell wire (4). Separate wires enough to connect the white/red wire to terminal screw 1 and the white wire to terminal screw (1). Backlit Door Control Button: Fasten to an inside garage wall with sheet metal screws (3) provided with Backlit Push Button. Drill 4mm holes and use anchors (6) if installing into drywall or concrete. [. . . ] · Apply grease to rail and trolley · The Outside Quick Release accessory 1702AML (if fitted) discon· Oil door rollers, bearings and hinges nects the Trolley from outside the garage in case of power failure. · DO NOT lubricate the opener itself · DO NOT APPLY grease to the door tracks 14 CHAMBERLAIN 1 YEAR LIMITED WARRANTY Motorlift ML500 Garage Door Operator Chamberlain Australia Pty Limited / Chamberlain New Zealand Limited (Seller) warrants to the original purchaser of the Motorlift ML500 Garage Door Operator (Unit) that it is free from defects in material and/or workmanship for a period of 12 months from the date of first purchase from the Seller. Please retain your proof-of-purchase in the unlikely event you require warranty service. If, during the limited warranty period, the Unit fails due to defects in materials or workmanship Chamberlain will, provided the defective part or Unit is returned freight and insurance prepaid and well packaged to the nearest Chamberlain office or authorised installer, undertake to repair or, at its option, replace any defective part or Unit and return it to the Buyer at no cost. [. . . ]