User manual CHAMBERLAIN MT5011E INTALLATION

[. . . ] INSTALLATION MANUAL MODEL MT5011E/BMT5011E MEDIUM DUTY DOOR OPERATOR with Now lt in Bui ceiver e adio R R I N TENDED INTENDED F O R P R O F ES S I O NA L E SSI I N STALLA TIO ON L INSTALLATI O N O NL Y Visit www. LiftMaster. com to locate a professional installing dealer in your area. Radio Receiver Built on Board 2 YEAR WARRANTY Serial # (located on electrical box) Installation Date 315MHz NOT FOR RESIDENTIAL USE A SAFETY DEVICE IS HIGHLY RECOMMENDED. TABLE OF CONTENTS SAFETY INFORMATION . 14-15 OPTIONAL SAFETY DEVICE CONFIGURATIONS . BACK COVER SAFETY INFORMATION WARNING WARNING Mechanical IMPORTANT NOTES: CAUTION WARNING Electrical When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. [. . . ] · Wiring for safety device to reverse. NOTE: The operator will automatically convert to B2 wiring (option D) when Monitored Safety Device is installed. (See accessories page for Monitored Safety Devices) · Timer to Close (TTC) feature not available. MONITORED SAFETY DEVICE A C2 WIRING TYPE WITHOUT MONITORED SAFETY DEVICE (Factory Default) · Momentary contact to open and stop with constant pressure to close. · Open override that reverses when closing by any opening device. · Wiring for safety device to reverse. NOTE: The operator will automatically convert to B2 wiring (option D) when Monitored Safety Device is installed. (See accessories page for Monitored Safety Devices) · Timer to Close (TTC) feature not available. NON-MONITORED SAFETY DEVICE ADVERTENCIA PRECAUCIÓN Sensing Edge Photo Eye RESET TO C2 WIRING TYPE (Factory Default) Remove any monitored safety devices. Disconnect then reconnect power to the operator. Press and hold the LEARN and STOP buttons until the LED goes out (approximately 3 seconds). Electrical Box Logic Board TO PROGRAM Press and hold the LEARN and CLOSE buttons until the LED goes out (approximately 3 seconds). Electrical Box Logic Board D7 U4 D6 D5 D4 014A1030 TP1 C9 C21 C20 J4 C32 R25 U1 C31 L5 AUX ANT AUX ANT J2 ^^^^ C18 R27 D14 K2 LT C29 R24 P1 LEARN LEARN STOP CLOSE OPEN 3 4 5 6 7 COM INTRLK STOP CLOSE OPEN STOP CLOSE OPEN D7 U4 D6 D5 D4 TTC LED 1 2 014A1030 TP1 C9 C21 C20 J4 C32 R25 U1 C31 D9 L5 ^^^^ C18 J2 R27 D14 K2 LT C29 R24 P1 LMEP1 LMEP2 AUX ANT AUX ANT LEARN LEARN STOP CLOSE OPEN 3 4 5 6 7 INTRLK STOP CLOSE OPEN STOP CLOSE OPEN 1 D14 LED TTC LED 1 2 D9 LMEP1 LMEP2 COM D14 LED 2 3 4 5 6 7 1 2 3 4 5 6 7 18 BASIC PROGRAMMING C B2 WIRING TYPE WITHOUT MONITORED SAFETY DEVICE Requires a non-monitored safety device. · Momentary contact to open, close and stop. · Open override that reverses when closing by any opening device. · Wiring for safety device to reverse. NOTE: The operator will automatically convert to B2 wiring (option D) when Monitored Safety Device is installed. (See accessories page for Monitored Safety Devices) · Timer to Close (TTC) feature not available. NON-MONITORED SAFETY DEVICE D B2 WIRING TYPE WITH MONITORED SAFETY DEVICE · Momentary contact to open, close and stop. · Open override that reverses when closing by any opening device. · Wiring for safety device to reverse. NOTE: The operator will automatically convert to B2 wiring when Monitored Safety Device is installed. (See accessories page for Monitored Safety Devices) · Timer to Close (TTC) feature available. MONITORED SAFETY DEVICE Sensing Edge Photo Eye TO PROGRAM Start with operator in factory default C2 mode. Press and hold the LEARN and CLOSE buttons until the LED goes out (approximately 3 seconds). Electrical Box Logic Board NO PROGRAMMING REQUIRED D7 U4 D6 D5 D4 014A1030 TP1 C9 C21 C20 J4 C32 R25 U1 C31 L5 AUX ANT AUX ANT J2 ^^^^ C18 R27 D14 K2 LT C29 R24 P1 LEARN LEARN STOP CLOSE OPEN 3 4 5 6 7 COM INTRLK STOP CLOSE OPEN STOP CLOSE OPEN TTC LED 1 2 D9 LMEP1 LMEP2 D14 LED 1 2 3 4 5 6 7 19 BASIC PROGRAMMING REMOTE CONTROLS SINGLE BUTTON REMOTE CONTROL Built in 315 MHz radio receiver permits as many as 20 Security® remote controls or dip switch remote controls in any combination. [. . . ] Door height or speed may exceed the range the operator can travel. NOTE: It is normal for the logic board LED to flash 7 times when power is applied or cycled to the operator. (Not a logic board failure. ) DIAGRAM Green Brake (BMT only) Blue* Blue* * If brake is not supplied, wires are capped separately Black L2 Black L1 Capacitor Yellow Yellow Red Red OPEN Motor CLOSE CLOSE OPEN LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN 7 STOP wires are capped together. LEARN Brown** Orange Purple Yellow Grey STOP LED 2 3 4 5 ** If interlock is not used, Brown** 6 Remove Jumper to install external door interlock. ANT Safety Limit Switch Open Limit Switch Grey Close Limit Switch 23 AUX ANT J2 TTC 1 REPAIR PARTS ELECTRICAL BOX 4 K2 K3 K4 2 K1 K5 1 3 SERVICE KITS ITEM PART # K1 K72-33872-1 DESCRIPTION ITEM 1 2 3 4 PART # 13-10024 23-10041 29-10338 K10-33850 SERVICE KITS DESCRIPTION Limit Nut (1) Limit Switch (1) Capacitor Cover Limit Switch Shaft Kit Complete with: Limit shaft, limit nuts, limit bearings, limit sprocket, washers, compression ring, roll pin and e-ring. K2 K72-12493 Limit Switch Kit Complete with: Limit nut retainer, switch plates, backup plate, depress plate, limit switches (3), standoffs, screws and locknuts. [. . . ]