User manual CHICAGO 94564

[. . . ] TRAILER 4' x 8' MODEL 94564 ASSEMBLY AND OPERATING INSTRUCTIONS This trailer's Hitch Coupler MUST be properly secured to the hitch ball of the towing vehicle. After assembly and attachment, pull up and down on the Hitch Coupler to make sure the hitch ball is fitting snugly in the Hitch Coupler. There must be no play between the hitch ball and Hitch Coupler. If there is play, tighten the Adjustment Nut until no play is present. [. . . ] Then secure the Safety Chain in place, using a Flat Washer (N) and M12 Nylon Nut (U). (See Figure H. ) Assemble the Tail Light Brackets (26) to the rear of the Rear Left Side Rail (1RL) and Rear Right Side Rail (1RR), using the M10 x 20 Bolts (A) and M10 Nylon Nuts (I). 4. 5. REV 07j SKU 94564 For technical questions, please call 1-800-444-3353. Page 13 6. Attach the License Plate Bracket (27) with the Left Tail Light (28L) to the Rear Left Side Rail (1RL), using the M10 x 20 Bolts (A) and M10 Nylon Nuts (I). NOTE: The Left Tail Light has a clear window at the bottom. (See Figure H. ) Attach the Right Tail Light (28R) to the rear of the Right Side Rail (1RR), using the M10 x 20 Bolts (A) and M10 Nylon Nuts (I). (See Figure H. ) Open the Lens of the Side Running Lights (24). Run the Wire Lead of a Side Running Light through the center hole located at the front end of the Front Left Side Rail (1FL). Then attach the Side Running Light to the Front Left Side Rail, using the 4mm Self Tapping Screws (P). (See Figure H . ) Run the Wire Lead of the remaining Side Running Light (24) through the center hole located at the front end of the Front Right Side Rail (1FR). Then attach the Side Running Light to the Front Right Side Rail, using the Self Tapping Screws (P). (See Figure H. ) Re-install the Lens on the two Side Running Lights (24). Have a qualified service technician install a 4-wire, 12 volt DC Connector in the trunk area of your vehicle. TAIL LIGHT ILLUM. RUNNING LIGHT (BROWN) GROUND (WHITE) GROUND (WHITE) U L. H. STOP & TURN (GREEN) F CONNECTOR F YELLOW E GREEN E CONNECTOR WIRE (FROM LIGHT) BROWN BROWN WIRE (FROM LIGHT) D WIRE CLIP D C BROWN YELLOW C RED BLACK A A RED BLACK GREEN B B BROWN FIGURE I 2. Locate the vehicle's Connector Plug near the Trailer's Coupler (7) and lay out the Trailer's Wiring Harness wires. (See Figure I. ) For technical questions, please call 1-800-444-3353. 7. Connect the Brown Wire to the vehicle's Left Tail Light by stripping, wrapping, and taping the Connector Plug. (See Figure I. ) Connect the Yellow Wire to the vehicle's Left Signal and Stop Light Wire. (See Figure I. ) Connect the Green Wire to the vehicle's Right Signal and Stop Light Wire. (See Figure I. ) NOTE: Some foreign vehicles may require an adaptor to convert their 5-wire system to a 4-wire vehicle Connector Plug. (See Figure I. ) Attach the White Ground Wire at the plug end of the Wiring Harness to the small hole on the Coupler Base (6) with a 1/4" Tapping Screw (not included). (See Figure I. ) Leave about 18" of wire beyond the Coupler (7). Then lay out the remaining wires along the Connecting Rails (3L, 3R) and Left and Right Side Rails (1FL, 1FR, 1RL, 1RR). [. . . ] Check tail lights before each use and after storage. Check brake lights before each use and after storage. Check electrical ground wiring before each use. 2. Tires before/after Electrical PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. [. . . ]