User manual CHICAGO 98614

[. . . ] SAFETY PRECAUTIONS AND WARNINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GENERAL INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. 1 ON-BOARD DIAGNOSTICS (OBD) II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. 2 DIAGNOSTIC TROUBLE CODES (DTCS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 24 5 Press ENTER button to enter Main Menu. Use UP/DOWN scroll button to select Diagnostics from the menu. Main Menu 1/6 Diagnostics DTC Lookup Review Data Print Data System Setup Tool Information ? 6 Press ENTER button to confirm. A sequence of messages displaying the OBD2 protocols will be observed on the display until the vehicle protocol is detected. If the scan tool fails to communicate with the vehicle's ECU (Engine Control Unit), a "LINKING ERROR!" message shows up on the display. Verify that the ignition is ON; Check if the scan tool's OBD II connector is securely connected to the vehicle's DLC; Verify that the vehicle is OBD2 compliant; Turn the ignition off and wait for about 10 seconds. Turn the ignition back to on and repeat the procedure from step 5. If the "LINKING ERROR" message does not go away, then there might be problems for the scan tool to communicate with the vehicle. Contact your local distributor or the manufacturer's customer service department for assistance. 7 You will be prompted to erase previously stored data. Review previously stored data thoroughly before erasing. 25 Diagnostic Erase previously stored data to save data from this test?YES NO If no data is stored in the scan tool, above prompt will not show up. 8 If you wish to erase the data, press ENTER button; if you do not want to erase the data, press ESC or use LEFT/RIGHT button to select NO and press ENTER to continue. 9 View a summary of system status (MIL status, DTC counts, Monitor status) on screen. Wait a few seconds or press any key for Diagnostic Menu to come up. System Status MIL Status Codes Found Monitors N/A Monitors OK Monitors INC ON 6 3 3 5 If more than one module is detected, you will be prompted to select a module before testing. Control Module Engine Module $A4 1/2 ? 26 Use UP/DOWN scroll button to select a module and press ENTER button. 5. 1 Reading Codes Reading Codes can be done with the key on engine off (KOEO) or with the key on engine running (KOER). Stored Codes are also known as "hard codes" or "permanent codes". These codes cause the control module to illuminate the malfunction indicator lamp (MIL) when emission-related fault occurs. Pending Codes are also referred to as "maturing codes" or "continuous monitor codes". They indicate problems that the control module has detected during the current or last driving cycle but are not considered serious yet. Pending Codes will not turn on the malfunction indicator lamp (MIL). If the fault does not occur within a certain number of warm-up cycles, the code clears from memory. 1) Use UP/DOWN scroll button to select Read Codes from Diagnostic Menu and press ENTER button. Diagnostic Menu Read Codes Erase Codes Live Data View Freeze Frame I/M Readiness O2 Monitor Test 1/11 ? 2) Use UP/DOWN scroll button to select Stored Codes or Pending Codes from the Trouble Codes menu and press ENTER button. 27 Trouble Codes Stored Codes Pending Codes 1/2 ? If there are no Diagnostic Trouble Codes present, the display indicates "No (pending) codes are stored in the module!" Wait a few seconds or press any key to return to Diagnostic Menu. 3) View DTCs and their definitions on screen. $09 1/5 P0118 Generic Engine Coolant Temperature Sensor 1 Circuit High The control module number, sequence of the DTCs, total number of codes detected and type of codes (Generic or Manufacturer specific) will be observed on the upper right hand corner of the display. [. . . ] Modules Present Unit of Measure ? 2) View modules present with their IDs and communication protocols. Modules Present ID Protocol _________________________ $11 ISO 9141-2 6. Print Data The Print Data function allows printing out diagnostic data recorded by the scan tool or customized test reports. · To print out retrieved data, you need the following tools: 98614 scan tool A PC or laptop with USB ports A USB cable 60 1) 2) 3) 4) 5) Place included CD into CD-Drive, or download applications from our website: www. harborfreight. com or our distributors' websites. Follow onscreen instructions on your computer to install applications. [. . . ]