User manual CHICAGO 99887

[. . . ] HIGH POSITION MOTORCYCLE LIFT 99887 SET uP aNd OPERaTING INSTRuCTIONS distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd. , Camarillo, CA 93011 Visit our website at: http://www. harborfreight. com Read this material before using this product. Failure to do so can result in serious injury. SaVE THIS MaNuaL. Copyright© 2008 by Harbor Freight Tools®. [. . . ] Lower the Lift all the way before leaving. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. 6. 7. 8. 9. SPECIFICaTIONS Maximum Lift Capacity Maximum Lifting Height Minimum Lifting Height Ram Travel Distance Between Base Legs 1100 Pounds 30" 2-1/2" 7-3/8" 20-3/8" 10. Always center the load directly over the two Arm Lifts. Always use the two Straps with Hooks to secure the motorcycle/ATV to the Lift before raising the load. Do not use the Motorcycle Lift for aircraft purposes. Do not allow anyone on the vehicle when using the Motorcycle Lift. Keep all bystanders a safe distance away from the vehicle. This Motorcycle Lift is designed for short term use only. Do not leave a load on the Lift for extended periods. Before lowering the Motorcycle Lift, make sure tool trays and all other tools and equipment are removed from under the Lift. SKU 99887 uNPaCKING When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. aSSEMBLY INSTRuCTIONS Read the ENTIRE IMPORTaNT SaFETY INFORMaTION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Page 4 For technical questions, please call 1-800-444-3353. TO PREVENT SERIOuS INjuRY FROM aCCIdENTaL OPERaTION: Release any load from the Motorcycle Lift before assembling or making any adjustments to the unit. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Attach the two Base Legs (12) to the Post (19) using four Bolts (11) and four Spring Washers (10). (See Figure a. ) 3. POST (19) NuT (14) NuT (14) LOWER LINKaGE (5) BOLT (6) uPPER LINKaGE (16) FIGuRE B BOLT (6) POST (19) BaSE LEG (12) Attach the upper portion of the Arm Lift (13) to the Upper Linkage (16) using one Bolt (6) and one Nut (14). Attach the lower portion of the Arm Lift (13) to the Lower Linkage (5) using one Bolt (6) and one Nut (14). (See Figure C. ) FIGuRE a BaSE LEG (12) NuT (14) uPPER LINKaGE (16) BOLT (6) NuT (14) SPRING WaSHER (10) aRM LIFT (13) BOLT (11) BOLT (6) 2. Attach the Upper Linkage (16) to the Post (19) using one Bolt (6) and one Nut (14). Attach the Lower Linkage (5) to the Post (19) using one Bolt (6) and one Nut (14). (See Figure B. ) FIGuRE C LOWER LINKaGE (5) 4. Attach the Jack Bracket (3) to the Lower Linkage (5) using one Shaft (22) and one Nut (14). [. . . ] Low hydraulic oil and/or Arm Lift assembly. Bleed system of excess air and fill with hydraulic oil. Do not attempt to lift objects over 1100 pounds. Turn the Release Valve fully counterclockwise. [. . . ]