User manual CISCO ATA 188

[. . . ] Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide (H. 323) Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www. cisco. com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Customer Order Number: OL-4008-01 THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. [. . . ] This causes the Cisco ATA to send all debug traces to that IP address. Value Type Extended IP address Default 0 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide (H. 323) OL-4008-01 5-35 Chapter 5 Optional Feature Parameters Parameters and Defaults Voice Configuration Menu Access Code 81 RingOnOffTime Description This parameter specifies the ringer cadence pattern, expressed as a triplet of integers "a, b, and c". · · · a--Number of seconds to turn the ring ON. b--Number of seconds to turn the ring OFF. c--The ring frequency, fixed at 25. Value Type List of three integer values, separated by commas Range 1-65535 Default 2, 4, 25 Recommended Values: · · United States --2, 4, 25 Sweden -- 1, 5, 25 Voice Configuration Menu Access Code 929 IPDialPlan Description This parameter allows for detection of IP-like destination address in DialPlan. Three values are valid: · · · 0--String is dialed as is and not treated as an IP address. 1--When the Cisco ATA detects two asterisks (**), IPDialPlan takes over. The user enters the pound (#) key to terminate the digit collection, and the interdigit timeout default is not used. 2--When IPDialPlan is set to 2, three asterisks (***) are required for IPDialPlan to take effect. All other values are currently undefined. Value Type Integer Range 0, 1 or 2 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide (H. 323) 5-36 OL-4008-01 Chapter 5 Parameters and Defaults Optional Feature Parameters Default 1 Voice Configuration Menu Access Code 310 DialPlan Description The programmable dial plan is designed for the service provider to customize the behavior of the Cisco ATA for collecting and sending dialed digits. The dial plan allows the Cisco ATA user to specify the events that trigger the sending of dialed digits. These events include the following: · · · · The termination character has been entered. The specified dial string pattern has been accumulated. The specified number of dialed digits has been accumulated. The specified inter-digit timer has expired. Value Type Alphanumeric string Range Maximum number of characters is 199. Default *St4-|#St4-|911|1>#t8. r9t2-|0>#t811. rat4-|^1t4>#. Voice Configuration Menu Access Code 926 Additional DialPlan Information The DialPlan section contains the following additional topics that describe commands and rules for creating your own dial plan: · · · · About Dial Plan Commands, page 5-38 Dial Plan Blocking (In Rule), page 5-39 'H' Rule to Support Hotline/Warmline, page 5-40 'P' Rule to Support Dial Prefix, page 5-40 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide (H. 323) OL-4008-01 5-37 Chapter 5 Optional Feature Parameters Parameters and Defaults About Dial Plan Commands The following list contains rules for Cisco ATA dial plans: · · · . This command can be used only at the end of a dial plan rule (for example, 1408t5- is legal usage of the - command, but 1408t5-3. . . >#--Defines the # character as a termination character. When the termination character is entered, the dial string is automatically sent. The termination character can be entered only after at least one user-entered digit matches a dial plan rule. Alternatively, the command >* can be used to define * as the termination character. tn-- Defines the timeout value n, in the unit of seconds, for the interdigit timer. Valid values are 0-9 and a-z, where a-z indicates a range of 10 to 36. rn--Repeat the last pattern n times, where n is 0-9 or a-z. The values a-z indicate a range of 10 to 36. Use the repeat modifier to specify more rules in less space. · · Note The commands ># and tn are modifiers, not patterns, and are ignored by the rn command. · · · |--Used to separate multiple dial plan rules. [. . . ] An endpoint can call or be called, and it generates or terminates the information stream. An integrated circuit (IC) providing central office-like telephone interface functionality. Networking solutions and access technologies for offices that are not directly connected to large corporate networks. SIP endpoint SLIC SOHO T TCP Transmission Control Protocol. Connection-oriented transport layer protocol that provides reliable full-duplex data transmission. [. . . ]