User manual CISSELL 28ES30

[. . . ] The warranty period on each new replacement part furnished by Cissell in fulfillment of the warranty on new equipment or parts shall be for the unexpired portion of the original warranty period on the part replaced. With respect to electric motors, coin meters and other accessories furnished with the new equipment, but not manufactured by Cissell, the warranty is limited to that provided by the respective manufacturer. Cissell's total liability arising out of the manufacture and sale of new equipment and parts, whether under the warranty or caused by Cissell's negligence or otherwise, shall be limited to Cissell repairing or replacing, at its option, any defective equipment or part returned f. o. b. Cissell's factory, transportation prepaid, within the applicable warranty period and found by Cissell to have been defective, and in no event shall Cissell be liable for damages of any kind, whether for any injury to persons or property or for any special or consequential damages. [. . . ] Use a separate trap for the spotting board; keep it clean and in good working condition for best performance. If steam line is gravity returned to boiler, omit trap. IMPORTANT: Before installing trap and connecting steam return line, open globe valve in steam supply connection and flush pipe dope, borings and other foreign matter, from steam connections and steam chamber within spotting board. Failure to do this may later cause trap trouble. Page6 VACUUM SPOTTING BOARD VACUUM SPOTTING BOARD MECHANICAL OPERATION Vacuum draws uniformly through the screen area on the nose of the board and the nose of the swinging sleeve board by pressing on the middle foot pedal. By pushing the swinging sleeve board back, the vacuum operates on the nose of the large board. By pulling the swinging sleeve board forward, vacuum operates on its nose. Changing the position of the swinging sleeve board operates a self-cleaning valve which gives full unrestricted passage for vacuum at all times. Steam is released from the spotting gun by pressing the left foot pedal as follows: a slight touch releases a feather of dry steam; partly down releases dry steam; half-way down releases moist steam; completely down releases wet steam. CAUTION: The steam emitted from the spray gun is very hot. Burns to face and hands may result from contact with live steam. Hot air for drying is released from the spotting gun by pressing the right foot pedal. Place gun in position approximately two inches above material. Now, with gun in rotary motion (heavy arrows), spray wet steam downward straight through spotted area. Ample wet steam under pressure dissolves watersoluable spots instantly. Concentrated vacuum keeps wetted area from spreading as it draws the wet steam through the garments (light arrows). FOR DRYING 4. With one foot, press both vacuum pedal and air pedal all the way down and clear moisture from gun before starting to dry. Hold gun only the width of gun nozzle above garment. 6. Now, move gun in a zig-zag motion sweeping it rapidly back and forth across wetted area for drying (heavy arrows). Actually, excess moisture blown out with compressed air, and wetted area dried rapidly with the strong suction from the concentrated vacuum. is is Page8 INSTRUCTIONS FOR ADJUSTING WET AND DRY STEAM VALVES Page9 VACUUM SPOTTING BOARD MODEL A PARTS & ASSEMBLY Page10 Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Part No. Nut 1/4 Split Lock Washer Page15 Page16 STEAM CHAMBER & VALVE ASSEMBLY COMPLETE (AIR VACUUM) - VSB180 STEAM CHAMBER & VALVE ASSEMBLY COMPLETE (STEAM VACUUM) - VSB186 Ref. 1 2 3 4 5 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Part No. [. . . ] Should packing leak after adjustment, add a V 13 Pack Ring which is split to permit easy installation without removing stem. After use, the old style packing becomes hard and brittle, causing valve stem to bind when pack nut is tightened. Remove hard packing and replace with three new V 13 Split Pack Ring. If leak continues, remove old packing and replace with two new V 30 pack rings. [. . . ]