User manual CISSELL AUCMAN150140

[. . . ] 4 submenus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This way, it is possible to for example in the beginning of a drying time work with a higher temperature - in order to achieve a quicker drying - while to the end, this temperature - to avoid shrinking of the linen - will be decreased. These programs can be built up manual, automatic or in combination of these two drying systems. Remark When no residual moisture measuring system is used, only manual drying system is possible. Drying time Example : Drying program 50 ° : Part 1 Part 2 Part 3 Cooldowntime Anti-crease 55° stop: 5 act: 60 15' 50° stop: 5 act: 60 5' 45° stop: 5 act: 30 drY1 45° stop: 5 act: 30 3' 30' stop: 120 act: 5 1-30 On the lower display a program number is mentioned. Select a program number by means of the upper or lower button. Confirm your selection with the middle button. If a "- sign" appears before the number, this means that this program number does not contain a program, and you go immediately to "FL. tE". XX On the upper display, the selected program number is given. "ProG" appears on the lower display. Now by pressing the upper button, you can possibly select out of "CoPY" or "dEL". CoPY: To copy a program to another program number. So, the program can be used as basis and this can save a lot of programming time (see further copying a program) dEL: To delete a program (see further deleting a program). Act (actiontime - default 30) On the lower display appears the time that the drum has to turn left or right. If necessary, change this program with the upper or lower button (5 to 120 seconds) and confirm afterwards with the middle button. You will go to "CY. on" or "XX-1". CY. on (Cycle on)(default 0) Here the pulsating function of the cycle contact can be programmed. The bottom display shows the time during which the cycle contact needs to be closed. Change this setting when necessary by means of the top or bottom button (0 to 40 seconds) and then confirm by means of the middle button. If "0" is selected, you proceed immediately to "XX-1". If "no" was selected in the technical menu with "Pr. CY", you proceed automatically to "XX-1" and this parameter is not shown. CY. of (Cycle off)(default 5) The bottom display shows the time during which the cycle contact (during pulsating function) needs to be opened. Change this setting when necessary by means of the top or bottom button (5 to 600 seconds) and then confirm by means of the middle button. This parameter is not shown when "0" was selected with "Cy. on". [. . . ] The residual drying and cool down time is still counting on the lower display. When during a drying or cool down time the door is closed again, "Push" is mentioned alternately with the program number (or "CooL"). This is a way to let you know that you have to push the middle button again to activate the program again. Remark : If the door is opened during the anti-crease time, the lower display shows "End" and the program stops immediately. 31 32 3 Standard programs The Pro/HC is equipped with 10 standard programs. Those programs can be started directly but cannot be changed. It is however possible to copy them to a program number between 1 and 30 and then be changed. [. . . ]