User manual CISSELL CF 19

[. . . ] - WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in your building. Clear the room, building, or area of all occupants. Immediately call your gas supplier from a neighbor's phone. [. . . ] Make-up air from outside building may enter enclosure from top or side walls. (See Dryer Make-Up Air Chart) Use constant diameter duct with area equal to the sum of dryer duct areas. EXAMPLE: Six 8 inch (204 mm)) diameter duct = one 19. 6 inch (498 mm) diameter duct in area. Use 20 inch (508 mm) diameter duct or diameter to match tube-axial fan. This separates the dryer air from room comfort air. If dryers use room air instead of outside air, the heat loss can be another 25 Btu/h (6. 3 kcal/h) for each cubic foot per minute (cfm) used. Zero inches clearance to combustible material allowed on sides and at points within 4 inches (102 mm) of front on top. Heat loss into laundry room from dryer fronts only is about 60 Btu/h per square foot (15 kcal/h per 0. 1m²). Flange mounted, belt driven tube-axial fan. Fan must run when one or more dryers are running. See suggested Automatic Electrical Control Wiring Diagram on previous page. In some instances, special fans are required to supply make-up air, and/or booster exhaust fans are required. Exhaust duct maximum length 14 feet (5 mm) of straight duct and maximum of two 90° bends. Use 45° and 30° elbows wherever possible. Do not install wire mesh or other restrictions in the exhaust duct. Use clean-outs in the exhaust duct and clean periodically when needed. Never exceed 0. 3 inches water column (. 8 mbar) static pressure in the exhaust duct. Inside surface of the duct must be smooth. Make-up air from outside the building may enter the enclosure from the top or side walls. The area of the opening must be a minimum of 210 square inches (135484 mm²) for each dryer. This will deliver the proper amount of make-up air at an air velocity of approximately 500 fpm (152 m/min) through the opening. Use barometric shutters in the inlet air opening to control air when dryers are not running. EXHAUST DUCT MAKE-UP AIR OTHER RECOMMENDATIONS TROUBLESHOOTING Other Recommendations To assure compliance, consult local building code requirements. [. . . ] (2 each) Motor mount Gasket, curved (2 each) Gasket, cork 8 (2 each) Washer, lock 5/16 (4 each) Screw, cap HH 5/16-18 (4 each) Washer, cut 5/16 (4 each) Page 51 PARTSSMALL GEAR REDUCERTM100 Quantity 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 TM103 TM104 TM105 TM107 TM108 TM101 TM110 TM112 TM115 TM117 TM102 TM120 TU2623 TU2839 TU3243 RC349 TM118 TU4787 TU3211 TM119 Housing Small Seal Small Open End Cap Small Bearing Cup Small Bearing Cone Worm 1-1/2 x 7-1/8 Large Bearing Cup Large End Cap 1/4 Pipe Plug Large Bearing Cone Worm Gear Oil Seal Cap Screw 3/8 - 16 x 1-1/2 Cap Screw 1/4 - 20 x 7/8 3/8 Internal Tooth Lockwasher 1/4 Internal Tooth Lockwasher Small Closed End Cap 3/8 - 16 Hex Nut 3/8 - 16 x 2-1/2 Screw Vent Plug 1/4 NPT 1 1 1 2 2 1 2 1 1 2 1 2 4 8 6 8 1 2 2 1 Page 52 MOTOR & GEAR REDUCER ASSEMBLY Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Part No. TU2317 510101041 TU6722 TU5241 TM100 TU1851 TU2831 RC347 TU15517 MTR303 TU33 IB140 TU4787 TU14414 VSB134 TU3246 TU4934 TU2846 TU2847 RC344 TU4684 TU8608 TU15516 510101040 TU7334 TU2833 Description BELT, V 4L-380 SHEAVE, AK39 (50 Cycle) SHEAVE, AK-51H (60 Cycle) KEY, 3/16 SQ. X 1" LONG REDUCER, GEAR-SMALL-METRIC WASHER WASHER, REG. [. . . ]