User manual CISSELL CF 439

[. . . ] The warranty period on each new replacement part furnished by Cissell in fulfillment of the warranty on new equipment or parts shall be for the unexpired portion of the original warranty period on the part replaced. With respect to electric motors, coin meters and other accessories furnished with the new equipment, but not manufactured by Cissell, the warranty is limited to that provided by the respective manufacturer. Cissell's total liability arising out of the manufacture and sale of new equipment and parts, whether under the warranty or caused by Cissell's negligence or otherwise, shall be limited to Cissell repairing or replacing, at its option, any defective equipment or part returned f. o. b. Cissell's factory, transportation prepaid, within the applicable warranty period and found by Cissell to have been defective, and in no event shall Cissell be liable for damages of any kind, whether for any injury to persons or property or for any special or consequential damages. [. . . ] Failure to do so will cause trap to leak. Make electrical connections in junction box on rear of machine, following applicable electric codes. Include a fused disconnect switch or circuit breaker with slow-blow characteristics and be capable of carrying 15 amps, 115 volts or 8 amps, 230 volts. Install the revolving form on the machine. Test the machine, following the OPERATING INSTRUCTIONS in this manual. Page 4 SAFETY PRECAUTIONS Please read these warnings before operating or servicing machine. To prevent burns, avoid contact with hot steam. Before service machine, close steam supply valve and purge lines. CAUTION: Shut off electrical supply before servicing to avoid electrical shock. Position foot switches at convenient location. Adjust shoulder form width by turning knob in either direction. Cissell form requires adjustment of the Waist, Hip and Lower control knobs. Disconnect and measure resistance of relay coil. A good coil should be between 240-360 ohms. Replace coil if not within these parameters. If wheel rubs or is stuck, loosen the set screws and align the wheel on the shaft. Measure the resistance of the black and white wires on the motor terminal board. Replace motor if not within these parameters. If relay, blower wheel, and motor are good, replace motor. Refer to the Installation Instructions and make corrections in installation if needed. Refer to steam line Installation Instructions. Install by-pass from supply header to return line. Return lines must be gravity fed to condensate tank. [. . . ] 24 Wooden Sleever* Front Paddle only Sponge only E Ring (3/16) Clamp Slide Support Pin Slide Spring Clip Clamp Slide Pivot Pin Waist Index Plate Hip & Lower Index Plate Control Slides Front Plate Front Latch Trigger Release Clamp Latch Rod Compression Latch Spring Latch Plunger Front Handle Assembly Rear Paddle only Sponge only Back Latch Front Paddle & Sponge Assembly Rear Handle Assembly Clamp Leaf Spring Rear paddle & Sponge Assembly Covered Spring Assembly Revolving Form Frame Locknut (1/4 - 28) Washer Page 14 WAIST, HIP, AND LOWER CONTROLS Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Part No. F322 F323 F321 F301 F300 F319 F318 F377 F324 F325 F490 V2 P39 F429 F439 F440 Description Waist Control Knob Hip Control Knob Lower Control Knob Spacer Spacer Actuating Lever Actuating Lever Bearing Pin Bearing Pin Connecting Link Draw String Lever Cotter Pin Yoke, Pin & Cotter Pin Tension Spring Hip Lever Rod Waist Lever Rod Ref. 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Part No. Description 040113282 Bead Chain (order by length) F442 Cord, Beads, & Couplings Set F443 2 Pins & 4 E Rings F888 E Ring F444 2 Pins & 4 E Rings F445 2 Pins & 4 E Rings F446 Swivel & Chain Coupling F447 Spacer F448 Lower Swivel Arm F449 Hip Swivel Arm F450 Lever F331 Bearing Pin F451 Lower Lever Rod F1003 Lower Lever Rod Assembly F1004 Hip Lever Rod Assembly Page 15 BASE ASSEMBLY PARTS Ref. [. . . ]