User manual CISSELL CF 487

[. . . ] WARNING: Purchaser must post the following notice in a prominent location: WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury ordeath. - Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. - WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in your building. [. . . ] 2) The Model C 75 ST has 2 pockets per dryer, each pocket has the above listed characteristics; both pockets have one 8" (203mm) exhaust manifolded into one 12" (305mm) exhaust duct for exhaust connection. 3) For the C 30 ST and the C 75 ST Models, the Required Make-up Air Area shown in the table should be doubled since it is shown per pocket, only. 4) E/S indicates an Energy Saving Model. Page 28 Exhaust and Venting DRYER AIR FLOW INSTALLATION Nothing is more important than air flow for the proper operation of a clothes dryer. A dryer is a pump which draws make-up air from the out-of-doors, through the heater, through the clothes and then forces the air through the exhaust duct back to the out-of-doors. Just as in a fluid water pump, there must be a fluid air flow to the inlet of the dryer, if there is to be the proper fluid air flow out of the exhaust duct. In summary, there must be the proper size out-of-doors inlet air opening (4-6 times the combined areas of the air outlet) and an exhaust duct, size and length of which allows flow through the dryer with no more than 0. 3 inches water column static pressure in the exhaust duct. In some instances, special fans are required to supply make-up air, and/or boost exhaust fans are required for both regular and energy saving models. Exhaust duct maximum length 14 feet (4. 3 mm) of straight duct and maximum of two 90° bends. Use 45° and 30° elbows wherever possible. Use 2 feet (0. 6 m) of straight duct on dryer before installing an elbow on energy-saver models only. Do not install wire mesh or other restrictions in the exhaust duct. Reference: Lighting and shut-down instructions and wiring diagrams are located on the rear wall of the dryer cabinet. The dryer must not be installed or stored in an area where it will be exposed to water and/or weather. Install dryer so that you can use short, straight venting. Turned elbows and long vent tubing tend to increase drying time. Longer drying time means the use of more energy and higher operating costs. Dry light-weight fabrics separately from heavy fabrics. You will use less energy and get more even drying results by drying fabrics of similar weight together. A clean lint screen helps give faster, more economical drying. Do not open the dryer door while drying. You let warm air escape from the dryer into the room. This saves having to re-start your dryer to remove wrinkles. 4. [. . . ] Gear Sheave (AK-46H) with Set Screw, 50 Hz. Motor Sheave (AK-34H) with Set Screw, 60 Hz. Motor Sheave (AK-39H) with Set Screw, 50 Hz. Belt Guard Mounting Shaft Key Small Gear Reducer (see separate page) Basket Motor (see Motor List page) Key Belt Adjusting Rod Right Angle Connector 1/2" Greenfield Cable Straight Connector Motor Drive Bracket 1/2" Greenfield Cable Fan Motor (see Motor List page) Motor Mount Weldment Top and Bottom Gasket Side Gasket Felt Seal Key Fan Wheel with Set Screws (50/60 Hz. ) 29 TU8206 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 TU7733 RC344 TU2846 TU2847 TU4934 TU5439 VSB130 TU2814 C249 TU3124 RC347 TU1851 TU2831 TU4787 VSB134 IB140 TU3211 TU4937 ---- Air Switch Assembly (See separate page) 8 x 1/2" Self Drill Screw (Pkg. [. . . ]