User manual CISSELL CISSIMAN38

[. . . ] Cissi Form Finisher Models FCCG FCCD FCFG FCAC MANUAL OWNER'S MANUAL CISSELL MANUFACTURING COMPANY HEADQUARTERS 831 SOUTH FIRST ST. BOX 32270 LOUISVILLE, KY 40232-2270 PHONE: (502) 587-1292 SALES FAX: (502) 585-3625 SERVICE/PARTS FAX: (502) 681-1275 MANUAL THIS MANUAL MUST BE GIVEN TO THE EQUIPMENT OWNER. MAN38 5/97 Page 1 WARRANTY The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from defects in material or workmanship for a period of one (1) year from the date of sale thereof to an original purchaser for use, except as hereinafter provided. With respect to non-durable parts normally requiring replacement in less than one (1) year due to normal wear and tear, including, but not limited to, cloth goods, valve discs, hoses, and iron cords, and with respect to all new repair or replacement parts for Cissell equipment for which the one (1) year warranty period has expired, or for all new repair or replacement parts for equipment other than Cissell equipment, the warranty period is limited to ninety (90) days from date of sale. [. . . ] PROBLEM: Revolving Form "drags" on base. TO CORRECT: Loosen F286 Bearing Lock Nut. Turn F287 Bearing Adjustment Screw COUNTER-CLOCKWISE. CHECK ADJUSTMENT: Replace revolving form on base. If perfectly adjusted, form will rotate freely and snugly on felt seal around top of base. If form is still too low. . . or too high. . . repeat adjustment until it is correct. PROBLEM: Revolving Form rides too high above base. TO CORRECT: Loosen F286 Bearing Lock Nut. Turn F287 Bearing Adjustment Screw CLOCKWISE. CHECK ADJUSTMENT: Replace revolving form on base. If perfectly adjusted, form will rotate freely and snugly on felt seal around top of base. If form is still too high. . . or too low. . . repeat adjustment until it is correct. Page 15 SOLENOID LINKAGE ADJUSTMENT TO ADJUST STEAM VALVE AND SOLENOID LINKAGE: 1. Set steam valve extension bar and solenoid lever at 90º as shown and tighten set screw. Adjust steam valve adjusting nuts until 1/32" to 1/16" gap is obtained as shown above and lock adjusting nuts tightly together. Page 16 MOT MOTOR MOUNTING DIMENSIONS Page 17 SERVICE CHART PROBLEM (1) No Steam CAUSE CAUSE 1A Steam Supply Valve "OFF" 1B Electric power"OFF" REMEDY Open valve in steam supply line. Inspect electric service for blown fuses, loose conections. Adjust switch away from cam with adjusting nuts. Replace panel, test and repeat if necessary. Inspect nameplate voltage and voltage on electrical parts, especially the solenoid. Check switch to see that it operates and will carry current. Check linkage between solenoid and steam valve for broken or loose parts. (See adjustment instructions) Inspect linkage and adjust according to instructions. Check to see that direction of flow in trap is correct and that trap is correct and that trap is in or below machine return line. Check to see that direction of flow is correct and valve not sticking. (2) Blower motor will start, steam won't start 2A Start switch not released by cam when control knob is pushed 2B Loose wires 2C Incorrect voltage of electrical parts 2D Defective start switch 2E Defective solenoid 2F Defective solenoid linkage (3) Leaking steam valve 3A Solenoid linkage adjusted incorrectly 3B Loose valve seat 3C Worn valve (4) Wet steam 4A Trap not operating 4B Trap installed incorrectly 4C Check valve installed wrong or sticking Page 18 PROBLEM (4) Wet steam (Cont. ) CAUSE CAUSE 4D Strainer clogged 4E Return line turned off 4F Steam Cycle too long 4G Improperly installed steam lines 4H Heavy condensate in supply line 4I Machine not individually trapped 4J Back pressure in return line REMEDY Inspect strainer and clean if necessary. [. . . ] 5/16" Split Lockwasher #8 x 5/8" S. M. S. F122 RC349 V2 IB139 VSB134 IB140 F819 P126 TU3210 TU2814 TU2793 Page 26 ALVE PARTS VALVE PARTS Ref. F287 F286 F285 FV101 OP547 FV106 F18 F894 F896 FV110 FV100 V36 P103 F359 FV103 V15 V16 FV104 V330 FV105 F358 Description Bearing Adjustment Scr. Bearing Lockout Bearing Support Box Valve Lever Locknut Collar Retainer Steam Spreader Drawband Drawband Eye Valve Ass'y CONSISTS OF REF. 10-20 Valve Body Valve Seat Gasket "E" Ring Valve Stem Small Locknut Teflon Disc Valve Disc Holder 30 Lb. [. . . ]