User manual CISSELL GENIEMAN59

[. . . ] With respect to electric motors, coin meters and other accessories furnished with the new equipment, but not manufactured by Cissell, the warranty is limited to that provided by the respective manufacturer. Cissell's total liability arising out of the manufacture and sale of new equipment and parts, whether under the warranty or caused by Cissell's negligence or otherwise, shall be limited to Cissell repairing or replacing, at its option, any defective equipment or part returned f. o. b. Cissell's factory, transportation prepaid, within the applicable warranty period and found by Cissell to have been defective, and in no event shall Cissell be liable for damages of any kind, whether for any injury to persons or property or for any special or consequential damages. The liability of Cissell does not include furnishing (or paying for) any labor such as that required to service, remove or install; to diagnose troubles; to adjust, remove or replace defective equipment or a part; nor does it include any responsibility for transportation expense which is involved therein. [. . . ] Align crotch; do not raise pants too high as crotch must remain loose in buck opening to prevent wrinkling of crotch area. To soften pleats (Before making respective pleat lays), push PRE-STEAM BUTTON. Steam Timer controls pre-steaming automatically. NOTE: Excessive moisture will de-lusterize Rayon acetates. This may be minimized by using "air" while steaming; or shortening of steam cycle by depressing fully "off " air switch. Do not use the pre-steaming operation on rayon acetates. 4. 5. 6. Smooth out material and lay each pleat separately, working from fly toward pleat being layed. Align pleat with leg crease; close pleat holder. If too much material is encountered during laying of pleats, trousers are too high on the buck and too low on the rear expander. If too little material is available to lay the pleat properly, the trousers may be too low on the buck and too high on the expander. Steam and Air Timers control steam followed by air automatically. Leg-out during the final phase of the automatic cycle of the Topper. 7. 8. Place creased trousers on hanger and make necessary touch-ups on Puff Iron before placing pants on finish rail. Page 8 POSITIONING PANTS ON TOPPER OPERATING INSTRUCTIONS (A) At "Start-Up" (or after "Idle Periods" of operation) preheat before operating: a. Adequate holding of the pleat lay during the air cycle is aided by the surface texture of the pleat clamp and the buck cover. Page 12 PANTS TOPPER BAG: KEEP BAG CLEAN. In operation, bag collects dust, lint, etc. , greatly reducing its efficiency. Launder bag at frequent intervals as determined by its soiled condition. The Cissell Pants Topper bag has a double liner to extend pad life and to distribute steam uniformily. REPAIR HOLES OR WORN SPOTS in bag to extend its useful life: REPLACE when worn beyond repair. A defective or worn bag will cause topper to operate unsatisfactorily. KEEP A SPARE BAG IN STOCK. CAUTION CAUTION Use only genuine CISSELL PT474 bags. The fabric for the Cissell Bag is especially woven (and cut to an exact pattern) to give the correct porosity and shape for proper steaming and drying. Remember, your CISSELL PANTS TOPPER depends on the bag for proper operation. Correct padding is necessary to obtain proper finishing. The Cissell buck pad is constructed of a high, heat-resisting synthetic air foam, and perforated for rapid steaming and full air flow through entire buck area. Replace a worn-out pad only with a Cissell perforated pad. [. . . ] and 110V. unit (3) Steam leaks Solenoid valve leaks continously Bead/nut fittings on preheater through buck tubes Loose teflon seat in solenoid (4) Water drips from Bead/nut fittings on preheater buck or support tubes. Ventilating fan moving air over buck and support Leaking steam solenoid valve. Supply line has loop or fall in horizontal run that is below machine inlet. Heavy condensate in supply header does not drain rapidly to boiler. [. . . ]