User manual CISSELL HD125

[. . . ] HD LAUNDRY DRYER Gas: Natural and LP Steam Electric Technical specifications Installation instructions Operating instructions Maintenance HD125 MAN HD2125 Cissell Manufacturing Co. 831 S. - 40232-2270 Tel: (502) 587-1292 - Fax: (502) 585-2333 Sales Fax: (502) 585-3625 - Service/Parts Fax: (502) 681-1275 THIS MANUAL MUST BE GIVEN TO THE EQUIPMENT OWNER 3/06 IMPORTANT NOTES - PLEASE READ For optimum efficiency and safety, we recommend that you read the manual before operating the equipment. Store this manual in a file or binder and keep for future reference. WARNING: Purchaser must post the following notice in a prominent location: WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury, or death. [. . . ] 6. NOTE It is best to run a properly sized bag of rags and/or old towels through one or two cycles prior to drying in service. This process will remove any films or residual coatings left by the manufacturing process. CAUTION Synthetic solvent fumes from dry cleaning machines create acids when drawn through the dryer. These acid fumes cause rusting of painted parts, pitting of bright plated parts and completely removes the zinc from galvanized metal parts, such as the tumbler basket. If the dry cleaning machines are in the same area as the tumbler, then the tumbler make-up air must come from a source free of solvent fumes. ABOVE 2, 000 FEET (610 M) ELEVATIONS ABOVE 2, 000 FEET (610 M) Input ratings shown on the rating plate (serial tag) are for elevations up to 2, 000 feet (610 m). For elevations above 2, 000 feet (610 m), rating should be reduced at a rate of 4% for each 1, 000 feet (305 m) above sea level. Page 29 OPERATING INSTRUCTIONS--TWO TIMER MODELS Page 30 OPERATING INSTRUCTIONS--TWO TIMER MODELS OPERATING INSTRUCTIONS--TWO TIMER MODELS OPERATINGINSTRUCTIONS--TWO TIMERMODELS 1. After loading the dryer with the water washed clothes load, close the loading door. For better drying, do not load dryer with combination of garments that twist. Turn the 60-minute drying timer to the desired drying time. The drying cycle light will be on and indicate the drying. The light shuts off when drying time is complete. Turn the 15-minute cooling cycle timer to the desired cool down time. After the drying cycle is completed, then the cooling cycle time will automatically operate. The cooling light will be on and indicate the cooling of the clothes load. The light shuts off when cooling time is completed. Temperature Selector--Select temperature per type of load being dried in the dryer. (figure 2 on page 26. ) High Heat--Mixed and heavy fabrics, set dial to 195°F (77°C). Normal--Cottons and linens, set dial to 170°F (77°C). Permanent Press Heat--Poly knit synthetics, blends, lightweight fabrics, set dial to 150°F (66°C). Low Heat--Delicate, sheer fabrics, easy-to-dry, set dial to 135°F (58°C). Thermometer--Use this with your temperature selection. [. . . ] of 6) 3/8" - 16 x 1" Cap Screw (Pkg. of 6) Large Bearing Cone & Cup Large Klozure 1/4" Pipe Plug 3/8" x 3" Set Screw Large End Cap 10 1/2 Dia. Small End Cap 6 3/4 Dia. TM225 Worm and Worm Gear Set (for TM200 ONLY) (only sold as set) Not Illustrated--TU3465 one pint of Cissell Transmission Oil Page 68 GAS BONNET ASSEMBLY REF NO. TU9614 CB36 OP267 PT196 RC344 TUX387 TUX352 TUX435 TU10946 TU13613 GA-00764-0 TU4605 DESCRIPTION Gas Manifold 1/4" - 20 x 1/2" Hex Head Screw 3/4" x 1/2" Steel Bushing 3/4" Strap 1/4" - 20 x 3/4" Hex Head Screw BSI Asm. [. . . ]