User manual CISSELL MANHD50.1

[. . . ] HD LAUNDRY DRYER Gas: Natural and LP Steam Electric Technical specifications Installation instructions Operating instructions Maintenance HD50. 1 MANHD50. 1 Cissell Manufacturing Co. 831 S. - 40232-2270 Tel: (502) 587-1292 - Fax: (502) 585-2333 Sales Fax: (502) 585-3625 - Service/Parts Fax: (502) 681-1275 THIS MANUAL MUST BE GIVEN TO THE EQUIPMENT OWNER 7/02 IMPORTANT NOTICESPLEASE READ For optimum efficiency and safety, we recommend that you read the manual before operating the equipment. Store this manual in a file or binder and keep for future reference. WARNING: Purchaser must post the following notice in a prominent location: WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death. - Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. [. . . ] Fan must run when one or more dryers are running. See suggested Automatic Electrical Control Wiring Diagram on previous page. Fan air flow (cfm) (m³/min. ) is equal to sum of dryer air flows, but static pressure (SP) is dependent on length of pipe and number of elbows. Barometric bypass damperadjust to closed flutter position with all dryers and exhaust fan running. Must be located within enclosure. 3. 4. 6. 7. CAUTION: Never install hot water heaters or other gas appliances in the same room as dryers. Never install cooling exhaust fans in the same room as dryers. CAUTION: Never exhaust dryers with other types of equipment. Page 21 Suggested Minimum Dryer Make-up Air Requirements Dryer Model C 30 ST C 75 ST C 110 C 110 E/S C 125 C 150 HD175 HD190 HD20. 1 HD30SL HD30. 1 HD50. 1 HD75. 1 HD80. 1 Dryer Pocket Capacity lb kg 30 13. 6 75 34 110 50 110 50 125 56. 7 150 68 175 79. 4 190 86. 2 20 9. 1 30 13. 6 30 13. 6 50 22. 7 75 34 80 36. 3 Maximum Air Flow Duct Size For Required Make-up Rate per Pocket Service Connection Air Area per Pocket cfm m3/h inch mm sq. inch cm2 450 765 6 153 87 561 1000 1700 12 305 192 1240 2200 3740 12 305 422 2723 850 1445 8 203 163 1052 2000 3400 12 305 384 2477 2250 3825 12 305 432 2787 2780 4726 12 305 534 3445 3000 5100 12 305 576 3716 450 765 6 153 87 561 600 1020 8 203 116 748 625 1063 8 203 120 774 850 1445 8 203 164 1058 1000 1700 8 203 192 1240 1000 1700 10 254 192 1240 Notes: 1) The Model C 30 ST has 2 pockets per dryer, each pocket has the above listed characteristics; each pocket is exhausted separately with a 6" (153mm) duct. 2) The Model C 75 ST has 2 pockets per dryer, each pocket has the above listed characteristics; both pockets have one 8" (203mm) exhaust manifolded into one 12" (305mm) exhaust duct for exhaust connection. 3) For the C 30 ST and the C 75 ST Models, the Required Make-up Air Area shown in the table should be doubled since it is shown per pocket, only. Page 22 Dryer Installation With Separate Exhaust (Preferred) DRYER INSTALLATION WITH SEPARATE EXHAUST (PREFERRED) For ductwork less than 14 feet (5 m) and 2 elbows equivalent and less than 0. 3 inches (8 mm) static pressure: NEVER exhaust the dryer into a chimney. NEVER install wire mesh screen over the exhaust or make-up air area. NEVER exhaust into a wall, ceiling, or concealed space. Make-up air opening from outside the building may enter the enclosure from the top or side walls. (See Dryer Make-Up Air Chart) Enclosure (plenum) with service door. This separates the dryer air from the room comfort air. If dryers use room air instead of outside air, additional heat loss can be another 25 Btu/h (6. 3 kcal/h) for each cubic foot per minute (cfm) (. 03m³/min. ) used. The installation clearance from all combustible material is 0" ceiling clearance for the first 4" (102 mm) from the front of the dryer. After the first 4" (102 mm), the ceiling clearance required is 6" (153 mm). The rear clearance required is 0", and the side clearance is 1" (26 mm). Heat loss into laundry room from dryer front panels is about 60 Btu/h per square foot (15 kcal/h per 0. 1m²). 3. 4. Page 23 Exhaust and Venting DRYER AIR FLOW INSTALLATION Nothing is more important than air flow for the proper operation of a clothes dryer. A dryer is a pump which draws make-up air from the out-of-doors, through the heater, through the clothes and then forces the air through the exhaust duct back to the out-of-doors. [. . . ] 1/2-13 X 1-1/4 ROTATION SENSOR PICK UP BRKT MOTOR, 1 HP 3PH BRACKET, MTR DRIVE-28X36 DBLMT WASHER, FLAT 3/8" NUT, HEX 3/8-16 SENSOR/INDUC/ROTAT/BALLUFF WASHER, SPLIT LOCK 3/8 SCREW, CAP HEX HD 3/8-16 NUT, HEX 1/4-20 WASHER, LOCK 1/4 MEDIUM WASHER, CUT 1/4" SCREW, CAP H. H. X 1-1/2 LONG ROD, BELT ADJUSTING ROTATION SENSOR BRACKET G/D SHEAVE, AK46-H (50 Cycle) SHEAVE, AK-34H (60 Cycle BUSHING (50 & 60 Cycle) Page 53 MOTOR ASSEMBLY- REVERSING Ref. No. Part No. Description 1 2 3 4 5 DA-11909-0 MTR315 TU6559 TU10998 VSB130 TU2814 TU5439 1/2HP 200-415/50-60/3 1/2HP 230-460/50-60/1 Sheave, 2. 0 dia. (50hz) Washer, cut 5/16 Washer, lock 5/16 Screw, cap HH 5/16-18 Page 54 IDLER ASSEMBLY Ref. [. . . ]