User manual CISSELL MUCMAN145000

[. . . ] The warranty period on each new replacement part furnished by Cissell in fulfillment of the warranty on new equipment or parts shall be for the unexpired portion of the original warranty period on the part replaced. With respect to electric motors, coin meters and other accessories furnished with the new equipment, but not manufactured by Cissell, the warranty is limited to that provided by the respective manufacturer. Cissell's total liability arising out of the manufacture and sale of new equipment and parts, whether under the warranty or caused by Cissell's negligence or otherwise, shall be limited to Cissell repairing or replacing, at its option, any defective equipment or part returned f. o. b. Cissell's factory, transportation prepaid, within the applicable warranty period and found by Cissell to have been defective, and in no event shall Cissell be liable for damages of any kind, whether for any injury to persons or property or for any special or consequential damages. [. . . ] Ball Bearing grease. CHECK VOLTAGE AND CURRENT: Your Topper is wired for a given voltage and current as stamped on name plate. Motor, Timers, Relays and Solenoid are for Single Voltage and Single current only. If machine is to be operated on any voltage and current, other than apecified above, THE MOTOR, RELAYS, TIMERS AND SOLENOID MUST BE REPLACED WITH UNITS CORRESPONDING TO THE VOLTAGE AND CURRENT ON WHICH THEY ARE TO BE OPERATED. GENERAL CLEANING: Every six months remove top cover, rear panel, front panel, blower and belt guards and clean thoroughly with a vacuum cleaner or air hose. AIR LINE OIL LUBRICATOR (MODEL B) Check Air Line Oil Lubricator and refill when less than half full. Use #10 weight oil. Page 9 POSITIONING PANTS ON TOPPER OPERATING INSTRUCTIONS (A) At "Start-Up" (or after "Idle Periods" of operation) preheat before operating: a. Lower pleat clamps onto padded buck; Operate Topper on "Manual Air" continuously for about one (1) minute. Either PRE-STEAM or AUTOMATIC Steam-Air cycle may be cancelled by pushing "OFF" Air Switch fully down. For Suede, Chamois or leather trimmed trousers, use manual air switch to provide air "while steaming", as full air pressure is required to hold pants taut during steaming cycle. Tops Trousers, slacks, shorts (Lightweight or Heavyweight) sizes 28 to 50. NOTE: Top small sizes, (including boys pants and small size ladies slacks) on 1M Puff Iron. If desired, the topper may be operated continuously with the control knob set in a postion providing the air pressure found most suitable by the operator. INSTRUCTIONS FOR OPERATING AIR PRESSURE CONTROL 1. Turn off electric power and remove Top Cover. Note: Check to see that the set screw of the Knob is tighten securely against the flat on the end of the rod. Place the pointer of the control knob at the low position (Fig. 2), with damper fully closed, push the pin on the damper stop (in center of rod) down until it hits the damper, tighten set screw securely. Rotate the pointer upward until the knob is in a horizontal position (Fig. 3), push the pin on the control knob stop (on the end of rod) against the damper frame as shown in Fig. Tighten set screw securely. 2. 3. Page 14 INSTALLATION OF BAG & BOOTS 1 . Center top edge of Pants Topper bag with center of waist clamp (A). Install retainer (B) over drawstring sheath (X), Fig. Loop drawstring around spool (P) as shown; pull loose ends of drawstring tightly and tie-off at (Z). 4 inside of bag on slide stud (E) and fasten securely with wing nut (F). [. . . ] Excessive tension will actually pull the shaft through the oil film and allow metal to metal contact. Noisy blower operation will also occur. The illustration at the right shows the preferred method for checking correct alignment of the pulleys. Excessive misalignment produces increased belt wear and can produce lateral motion of the wheel and shaft to the point that considerable noise can develop. Page 19 FOOT SWITCH REPLACEMENT (Part No. AF177) INSTRUCTIONS - Refer to illustration. [. . . ]