User manual CISSELL PANTOP24VMAN594

[. . . ] Pants Topper Model A Model B 24 Volt OWNER'S MANUAL CISSELL MANUFACTURING COMPANY HEADQUARTERS 831 SOUTH FIRST ST. BOX 32270 LOUISVILLE, KY 40232-2270 PHONE: (502) 587-1292 SALES FAX: (502) 585-3625 SERVICE/PARTS FAX: (502) 681-1275 THIS MANUAL MUST BE GIVEN TO THE EQUIPMENT OWNER. MAN594 05/00 Page 1 WARRANTY The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from defects in material or workmanship for a period of one (1) year from the date of sale thereof to an original purchaser for use, except as hereinafter provided. With respect to non-durable parts normally requiring replacement in less than one (1) year due to normal wear and tear, including, but not limited to, cloth goods, valve discs, hoses, and iron cords, and with respect to all new repair or replacement parts for Cissell equipment for which the one (1) year warranty period has expired, or for all new repair or replacement parts for equipment other than Cissell equipment, the warranty period is limited to ninety (90) days from date of sale. [. . . ] Leg-out during the final phase of the automatic cycle of the Topper. 7. 8. Place creased trousers on hanger and make necessary touch-ups on Puff Iron before placing pants on finish rail. Page 11 OPERATING INSTRUCTIONS MODEL B CAUTION: Timer Adjustments STEAM: Must not be greater than 6 seconds (Average setting 4-5 Seconds) AIR: Must not be less than 20 seconds (Average Setting 25 Seconds) NOTE: Straighten Pockets; Button Pocket Flaps; Button or Snap front of Waistband if you desire, But Do Not Close Zipper. Step on foot switch and the waist expander moves forward automatically. Lift trousers onto form, placing back center of waist band high onto waist expander. Pull trousers forward holding taught at fly. Continue to hold forward tension on trousers, step off foot switch. Allow automatic tension of waist expander to draw front of trousers onto face of buck. Lower waist clamp, clamp trousers to buck. Adjust and center pants to highest position on buck. Align crotch; do not raise pants too high as crotch must remain loose in buck opening to prevent wrinkling of crotch area. To soften pleats (Before making respective pleat lays), push PRE-STEAM BUTTON. Steam Timer controls pre-steaming automatically. NOTE: Excessive moisture will de-lusterize Rayon acetates. This may be minimized by using "air" while steaming; or shortening of steam cycle by depressing fully "off" air switch. Smooth out material and lay each pleat separately, working from fly toward pleat being layed. Align pleat with leg crease; close pleat holder. If too much material is encountered during laying of pleats, trousers are too high on the buck and too low on the rear expander. If too little material is available to lay the pleat properly, the trousers may be too low on the buck and too high on the expander. Steam and Air Timers control steam followed by air automatically. Leg-out during the final phase of the automatic cycle of the Topper. To remove trouser from buck step on foot switch again. Place creased trousers on hanger and make necessary touch-ups on Puff Iron before placing pants on finish rail. Page 12 REPLACING THE CONTROL SWITCHES 1. Install new switches and spacers in reverse order. Page 13 AIR PRESSURE CONTROL OPERATION Normally, set the air pressure control knob horizontally in the position illustrated, (Fig. [. . . ] Turn Switch upside down and remove screws (A). Remove washers, plate, insulation, and switch. Remove wires from old switch and install on new switch. Re-install switch, insulation, plate, washers, screws, base plate, screws. Foot Switch Assembly - Part No. [. . . ]