User manual CISSELL PANTOPAMAN39

[. . . ] Pants Topper Model A MANUAL OWNER'S MANUAL CISSELL MANUFACTURING COMPANY HEADQUARTERS 831 SOUTH FIRST ST. BOX 32270 LOUISVILLE, KY 40232-2270 PHONE: (502) 587-1292 SALES FAX: (502) 585-3625 SERVICE/PARTS FAX: (502) 681-1275 MANUAL THIS MANUAL MUST BE GIVEN TO THE EQUIPMENT OWNER. MAN39 9/98 2C WB Page 1 WARRANTY The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from defects in material or workmanship for a period of one (1) year from the date of sale thereof to an original purchaser for use, except as hereinafter provided. With respect to non-durable parts normally requiring replacement in less than one (1) year due to normal wear and tear, including, but not limited to, cloth goods, valve discs, hoses, and iron cords, and with respect to all new repair or replacement parts for Cissell equipment for which the one (1) year warranty period has expired, or for all new repair or replacement parts for equipment other than Cissell equipment, the warranty period is limited to ninety (90) days from date of sale. The warranty period on each new replacement part furnished by Cissell in fulfillment of the warranty on new equipment or parts shall be for the unexpired portion of the original warranty period on the part replaced. [. . . ] Align Pants Topper Bag (G) on buck (Fig. Pull drawstrings tight toward top of buck so that drawstring sheath (K) is equally distributed around outer edges of perforated metal buck (H). Holding strings tight, tie-off to eyelet (L). Install Buck springs (S) by placing hooks over drawstring through sheath (K) as illustrated in Fig. INSTALLATION OF BOOTS Pull boots (R) Fig. To install new boots, pull down over frames. See that boot frames are tight against buck. Page 11 PLEAT ASSEMBLY INSTALLA ALLATION PLEAT SETTER COVER ASSEMBLY INSTALLATION 1. Place cover over pleat clamp (E), pull draw strings (K) tight and tie. Hook one end of each pleat clamp spring (M) on left side of cover, pull tight and hook on right side of cover. Adjustable Clamp Support OVAL PLEAT ADJUSTABLE OVAL PLEAT CLAMP ADJUSTMENT WITH ADJUSTABLE CLAMP SUPPORT ILLUSTRATION REFER TO ILLUSTRATION ABOVE. Loosen cap screw (A) in arm expander and cap screw (B) in adjustable support. Rotate and slide arm (C) in counterweight (D) to position pleat clamp (E) on buck. Place pleat clamp in vertical position and align inside edge of pleat clamp with edge of buck crotch (F). Apply pressure on arm knob (G) to provide pressure between pleat clamp (E) and buck. Hold pressure and retighten cap screw (A) of arm expander. With a thin card (H) check uniformity of pressure between edges of pleat clamp (E) and buck. If unequal, rotate pleat clamp slightly to obtain a uniform pressure around all edges. Re-tighten nut (B) of adjustable support. Note: Whenever tightening nut (B), do not apply pressure to knob (G) or arm (C), as this will disturb the pleat clamp setting. If pleat clamp (E) makes an impression (too tight), loosen cap screw (B) and rotate adjustment nut (J) counter-clockwise to reduce pressure. If pleat clamp does not hold pleat (too loose), loosen cap screw (B) and rotate adjustment nut (J) clockwise to increase pressure. Retighten cap screw (B). 2. 3. 4. 5. 6. B. NOTE: Each pleat clamp must engage the padded buck uniformily with a slight pressure. Heavy pressure may produce a hard finish and show seam imprinting. [. . . ] More than one machine connected to trap. Back pressure in steam return line. (6) No Steam-Steam Operating circuit relay (SR) relay (SR) does open at contact D (Steam not operate Timer Relay, STR) when Pre-steam Coil, Relay (SR) open button is pushed Operating circuit relay (SR) open at either contact N (manual oir switch), or contact P (Pre-steam pushbutton switch) Replace Relay Test contacts N and P; replace defective switch or push-button switch. Page 20 SHOOTING TROUBLE SHOOTING SERVICE CHART TROUBLE (6) Continued No Steam-Steam relay (SR) does not operate when pre-steam button is pushed. (7) No Steam or Air, Steam relay (SR) does not operate when Automatic button is pushed CAUSE CAUSE REMEDY Relay (SR) hums, when energized, Replace relay (SR) doesn't operate; coil partially shorted Relay (SR) hums, when energized, Replace with correct voltage relay (SR) doesn't operate; wrong voltage relay Operating circuit relay (SR) open at contact F (Automatic relay AR) Operating circuit relay (AR) open at contact N (Manual air switch) or contact Q (Automatic push-button) Coil relay (AR) open Relay (AR) hums when energized, doesn't operate, coil partially shorted Relay (AR) hums when energized, doesn't operate, wrong voltage relay (8) No Steam, steam Contact P (Pre-steam button) does timer relay remains not open energized, prevents Contact Q (Automatic Push-button) operation of steam does not open relay (SR), when Contact A (Steam Relay SR) doesn't Pre-steam button open when coil (SR) is de-energized is pushed. Contact F (Automatic relay AR) does NOTE: Timed Air not open when coil of (AR) is deonly when Automatic energized button is pushed Defective Air timer (AT), timer has no time-out, may have bad motor, or contact M may be welded closed Air timer does not time-out, wrong voltage timer (9) Timed Steam Holding circuit for Steam Relay (SR) Stops, when Preopen at contact A (SR) steam button is Holding circuit for Steam relay (SR) released. [. . . ]