User manual CITADEL XR2-ENGINEERING INFORMATION

[. . . ] XR2/ XR2+ Features Power Intruder alarm system Engineering Information RKP PART SET 8z MEM 4 REMOTE 8 6 OUTPUT 5 09 SET ÿ ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 Tamper Attack 8 zones, all programmable for Security, Fire, 24H Fire, PTS or keyswitch applications PA input Tamper input Outputs for Bell and Strobe 4 Access level Codes, User 1, User 2 and Engineer and Duress, all programmable 3 fully selectable part set programs Chime on any zone 8 event memory Programmable timers including bell cut off Walk Test facilities Quick set feature Remote keypad with on board PA and illuminated keys Option for connection of Lighting controllers Options to connect up to four remote keypads / Lighting controllers NVM for protection of engineer programme 6 digital outputs for a wire-in digital communicator, Red Care STU or dialler Service warning indicator, programmable between 100 and 800 set and unset events Battery capacity of up to : 2. 1Ah in XR2 enclosure 7Ah in XR2+ enclosure Features 0 5 Chime 1 6 Omit 2 7 Reset 3 8 Prog 4 PA 9 Set Day Power 8SP 403 XR2+ G3 panel with remote LED keypad ÿ ÿ ÿ ÿ ÿ ÿ ÿ ÿ ÿ ÿ ÿ ÿ ÿ ÿ ÿ ÿ ÿ Power ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 Tamper Attack 0 5 Chime 1 6 Omit 2 7 Reset 3 8 Prog 4 PA 9 Set Day Power Accenta/!mini 8SP 404 XR2 G3 panel with remote LED keypad The above intruder system is designed to comply with the installation requirements of BS 4737 1986/87. This manual provides information on Installation design, panel fixing, wiring, power up and programming of the intruder panel. 4188-694 issue 1_8/01 1 Downloaded from: http://www. guardianalarms. net Engineering information Contents Features - - - - - - - - - - - - - Installation Design - - - - - - - - Fixing - - - - - - - - - - - - - - Wiring the system - - - - - - - - Tamper network - - - - - - - - - Connecting Remote Keypads / Lighting controllers - - - - - - - Fixing the Remote Keypad (RKP) Security zones - - - - - - - - - - Push to set zone - - - - - - - - - Remote keyswitch zone - - - - - Fire zone - - - - - - - - - - - - PA circuit - - - - - - - - - - - - Extension speaker - - - - - - - - Bell Output (External sounder) - - 13V Supply output - - - - - - - - Set - - - - - - - - - - - - - - - Remote signalling Input and Outputs 1 2 3 4 4 5 5 5 6 6 7 7 8 8 9 9 9 11 12 12 13 13 13 13 13 13 14 15 15 15 16 17 18 18 19 19 20 21 22 23 24 25 26 27 31 31 32 Citadel XR2/XR2+ G3 Intruder system Installation Design The purchase of this alarm system represents a major step forward in the protection of the property and its occupants. It is important to plan the installation before proceeding and then follow the procedures and advice contained in this manual. [. . . ] Where an intruder alarm is shortly followed by a restore at the ARC, this can be used to filter the alarm. c. 10 4188-694 issue 1_8/01 Citadel XR2/XR2+ G3 Intruder system Engineering information Factory set condition User code 1 - User code 2 - Duress Code - Engineer Code Bell Duration Bell Delay - - Program 1 Zone 1 - - Zone 2 - - Zones 3. . . 8 Exit time- Entry - - Exit mode Program 2 Zone1 - - Zone 2 - - Zone 3. . . 8 Exit time- Entry time Exit mode Program 3 Zone 1 - Zone 2 - Zone3. . . 8 Exit timeEntry time Exit mode 0123 Not programmed Not programmed 9999 20 minutes No delay Flag A Silent PA - - - - - - RKP PA Enable - - - Engineer Reset- - - - Anti Code Reset - - - Door bell on push to set Single key setting - - Strobe on setting - - - External bell on Fire - Flag B Communicator Output active high - - - - - Line Fail active high - - - - - User Reset PA - - - User Reset Fire - - - Program 1 to report - Program 2 to report - Program 3 to report - Rearm counter - - - Service counter - - - Site Code - - - - - - Light Controller Light Threshold Light Hold Time Light Channel 1 Light Channel 2 Light Channel 3 Light Channel 4 Light Channel 5 Light Channel 6 Light Channel 7 Light Channel 8 - - - - - - - Timed Time Inhibited Immediate 30seconds 30seconds timed - - No Yes No No No No No No - - - - No (active low) No (active low) No No Yes Yes Yes 3 (re-arms) Off 00 Factory set condition - - - - - - Timed Time inhibited Immediate 30seconds 30seconds Disabled - - - - - - - Timed Time Inhibited Immediate 30seconds 30seconds Disabled Zones 1. . . 8 None programmed None programmed None programmed None programmed None programmed None programmed 300mS ALL zones Security Zones - - - Standard Fire zones 24 hour Fire zones - Push to set zones - - Keyswitch zones - - Double Knock zones Omit prevent zones- Zone debounce period - - - - - 50% 30 seconds No zones assigned No zones assigned No zones assigned No zones assigned No zones assigned No zones assigned No zones assigned No zones assigned 4188-694 issue 1_8/01 11 Engineering information Citadel XR2/XR2+ G3 Intruder system Note: The panel is not supplied with wire links for unused zones. All unused zones must be programmed out by setting them to disabled using the Zone Type function see page 20. First Power up To power up for the first time: a. Check that the factory fitted links are connected to terminals PA, TAMP and T-A. Fit the battery wires to the BATT terminals on the PCB, Red to + and Black to -. Panel BATTERY b. Mains Connection The mains power should be connected using a 3 core cable of not less than 0. 75mm sq. from a fused spur to the mains connector inside the control panel. The 2A fused spur must be located close to the control panel. Dedicated mains supply from consumer unit. F1 Board J4 +BATT AC 1. 6A (red) + Black - N E L 125mA Fuse 2A Fused Spur unit Panel BATTERY F1 Board J4 +BATT AC First Power up 12V battery Transformer c. On connecting the battery the system will now go into alarm condition and Tamper is indicated Tamper 1. 6A and there is an audible (red) + Black - N E L 125mA Fuse Transformer d. Alarm. Fit the cover to hold down the tamper spring at the bottom centre of the PCB. 12V battery e. Enter the user code: 0 1 2 3 (factory set at 0123). The alarm condition will cease and the system will go to Day mode . Immediately enter the engineer code Prog Day Note: The mains supply must be connected by a technically competent person and according to current IEE regulations. Caution: To avoid the risk of electrical shock you must always totally isolate the mains supply before opening the control panel cover(s). Mains Input Fuse rating: 125mA, 250V type T (anti surge) and of a type approved to IEC 127 part 2 sheet III. On connecting the mains supply to the panel the power indicator is lit. Power f. . The system is now in Engineer program mode and can be programmed. Note the Tamper 9 9 9 9 ÿ Tamper indicator is lit. 12 4188-694 issue 1_8/01 Citadel XR2/XR2+ G3 Intruder system Engineering information Testing the system Complete the wiring of the system and then: System indications Day Power ÿ ÿ ÿ ÿ - Unset system indication Fully test the system and ensure it is fault free. Fill in the installation log at the back of the manual and retain if for future reference. Finally explain the operation of the system to the end user. The Operating Instructions are attached to the centre of this manual. Detach them and leave them with the user. Power - Set system indication To enter Engineer program mode Note: The factory configured engineer's access code is 9999. If however this code is changed then enter the appropriate code. Prog ZONE 1 - 8 Momentarily On Engineer program mode The panel may be programmed to suit a wide variety of installations. Once the engineer program mode has been accessed, each configuration may be changed in any order. As each configuration is completed the system will automatically return to top level of engineer program mode. Before entering engineer program mode the system should be in the Day mode, with the Day and Power indicators lit. Keys 9 9 9 9 Acknowledge Tamper Day To Exit Engineer program mode Reset Day LED steady On indication LED flashing indication LED Off o/p ARC Output to Alarm Receiving Centre To reset panel to Factory set conditions Caution: All configurations of the panel are restored to factory `default' conditions. Within 5 seconds of powering up the panel Reset Reset Internal sound Sound description NOTE: In general a flat beep is an indication of an incorrect key press. [. . . ] The following points outline the most common installation and commissioning faults. As supplied the user code is 0123 and the engineer code is 9999. Both codes will revert back to these default settings on clearing the NVM. The Engineer Program is accessed directly from Day mode via the engineer code. [. . . ]