User manual CITIZEN WATCH C65

[. . . ] 17 16 18 18 19 19 20 20 21 22 23 15 4 1 16 17 21 22 23 24 15 1 4 24 2 2 5 5 . 13 KM 13 30 12 30 11 11 12 35 35 10 10 40 90 40 90 5 4 5 4 50 50 55 55 60 NAUT. 70 70 ST AT . 8 0 8 0 English Please charge the watch fully before use by exposing it to light. When the watch does not operate according to the instruction manual, it is insufficiently charged. Charge the watch for at least 3 hours approximately 20 cm (8 in) away from a fluorescent or incandescent lamp (30 W) as a light source. [. . . ] When the crown is pulled out to the second click (city setting position), the watch enters the city name correction state. Turn the crown to change the display of the registered city name to "-- -- -- ". After canceling registration, return the crown to the normal position. 42 43 <All-Reset Procedure> 4. This fully lit display is canceled when the crown is returned to the normal position. · After canceling, a confirmation tone is sounded after which each of the hands perform a demonstration movement in the order of the second hand, minute hand , UTC minute hand, UTC hour hand and 24 hour hand to indicate that the all-reset procedure is finished. · After the demonstration movement, pull the crown out to the second click to switch the watch to the watch base position setting state. Always make sure to set the 0 position (base position) for the hour hand, minute hand, second hand, 24-hour hand and UTC hour and minute hands while referring to "5. Checking 0-Position of Each Hand <0-Position Correction>". Note: · After setting the 0 position (base position) for each hand, correctly reset the time, calendar and other modes before using the watch. 1. Turn the crown to set the mode hand to the chronograph [CHR] mode. Pull out the crown to the second click (0-position correction mode). · The second hand, minute hand, hour hand, 24 hour hand, UTC hour hand and UTC minute hand rapidly advance to the 0 position stored in memory. Press buttons (A) and (B) simultaneously and then release. · All segments of the digital display are shown when either of the buttons is released. 44 45 15. Functions Unique to Solar-Powered Watches Normal display When the watch becomes insufficiently charged If the watch continues to be insufficiently charged When power generation stops as a result of light not shining on the watch Insufficient Charging Warning Function Analog display: Two-second interval movement Digital display: CHARGE mark flashes Stopped Analog displays: Hands stop moving Digital display: The entire display goes out Power Save 1 When Power Save 1 continues for 3 days When power generation resumes as a result of light shining on the watch When the watch is charged When the time is set while charging is still insufficient Time Setting Warning Function Power Save 2 Can be set arbitrarily When the watch is sufficiently charged and the time and date are set Analog display: Hands stopped at base position Digital display: Display flashes in initial setting state (12:00:00, UTC or January 1 SA UTC) Manual Power Save When the watch is exposed to light and the digital display begins to flash 46 47 [Insufficient Charging Warning Function] (Analog Display) Regardless of the display (mode) of the watch at the time, when the watch becomes insufficiently charged, the watch changes to the time display and the second hand begins to move at two-second interval movement. Although the 24 hour hand, hour hand and minute hand continue to keep the correct time, the watch stops after about 1. 5 days have elapsed after the insufficient charging warning function is activated. When this happens, charge the watch by exposing to light so that it returns to one-second interval movement. However, if the watch again becomes insufficiently charged without setting the time after it has been sufficiently charged by exposing to light as a result of having stopped due to being insufficiently charged, it will not return to the normal display unless the time is set after again sufficiently charging. 2sec 2 sec (Digital Display) "CHARGE" flashes on digital display area 2 in all modes. <Digital Display in Each Mode> · The watch displays the normal time display regardless of the position of the crown (pulled out to the first or second click) in each mode except for the calendar mode. · When the watch is in the calendar mode, the normal date display is displayed regardless of the position of the crown. Notes: · Crown operations do not function (except for mode switching (with the crown in the normal position)) in any of the modes. · Button operations do not function, except for changing the city name (UP/DOWN), in any of the modes. · The alarm tone does not sound even if it is set. [. . . ] Water may enter the watch and compromise water-resistance. · If the watch is used in seawater, rinse with fresh water afterward and wipe with a dry cloth. 68 69 metal band. If your watch is not water-resistant, take it to your dealer. NOTE: Avoid using solvents (thinner, benzine, etc. ), as they may mar the finish. CAUTION: Operating environment · Use the watch within the operating-temperature range specified in the instruction manual. [. . . ]