User manual CITIZEN CBM-231

[. . . ] LINE THERMAL PRINTER MODEL CBM - 230/231 CBM-230/231 User's Manual Declaration of Conformity Manufacturer's Name : Manufacturer's Address Declare the Product Product Name Model Number(s) : Japan CBM Corporation : CBM Bldg. , 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan Thermal Printer CBM-230 Series (CBM230R, CBM230P, CBM231R, CBM231P) (S. No. 95Y0001 ~ ) Conform to the following Standards LVD EMC : EN60950: : EN55022: : EN61000-3-2: : EN50082-1: : IEC801-2: : IEC801-3: : IEC801-4: 1992+A1+A2 : 1993 1994 Class A 1995 1992 1991 4KV CD, 8KV AD 1984 3V/m, 27MHz-500Mhz 1988 0. 5KV Signal Line, 1KV AC mains Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336EEC, 92/31/EEC, 93/68EEC" Place Date Tokyo, Japan March, 1998 Full Name: Mikio Moriya Position: General Manager R & D Department Europe Contact : Signature Norco Declaration AB Box 7146 S-250 07 Helsingborg Sweden Warning : This is a Class A products. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This declaration is applied only for 230V model. CITIZEN CBM-230/231 User's Manual IMPORTANT SAFETY INSTRUCTIONS · · · · · · Read all of these instructions and save them for future reference. Follow all warnings and instructions marked on the product. [. . . ] When it has no data, however, line feed is done. (3) Printing paper feed command (LF) Code : [0A]h Prints the data in the internal input buffer and feeds the line(s) based on the set line feed rate. (4) Setting the right space amount of the characters (ESC SP n) Code : [1B]h + [20]h + n * {0 n 20} The data is described with the hexadecimal code. Set the right space of the amount of the character in term of dots (in an increment of 1/203 inch). In the double width magnification mode, the right space amount is double the set amount. 28 CITIZEN CBM-230/231 User's Manual (5) Specifying collectively the print mode (ESC !n) Code : [1Bh] + [21h] + n * {0 n FF} The data is described with the hexadecimal code. Specifies the print mode. Each bit of n has the following meaning. Bit 0 1 2 3 4 5 6 7 Function Character font Undefined Undefined Highlighting Vertical double magnification Horizontal double magnification Undefined Underline Value 0 Font A 1 Font B Cancel Cancel Cancel Cancel Specify Specify Specify Specify · Four-fold characters are formed by simultaneously specifying both vertical and horizontal double magnifications. · The entire printed character width is underlined. However, the characters skipped by the horizontal tab are not. The 90°C ­right-turned characters are also not underlined. · An underline width is set by ESC ­. " (6) Specifying/canceling the download character set (ESC % n) Code : [1B]h + [25]h + n * {0 n FF} The data is described with the hexadecimal code. Specifying or cancels the download characters. The download characters and download bit images cannot be defined simultaneously. The lowest bit has the following meanings. n0 = 0 : Cancels the download character set n0 = 1 : Specifying the download character set 29 CITIZEN CBM-230/231 User's Manual (7) Defining the download characters (ESC & s n m a {D1 D2 ~ Dn}) Code : [1B]h + [26]h + s + n + m +a + Dn * {s = 03} {20 n 7E} {20 m 7E} {For the Font A; 0 a 0C, For the Font B; 0 a 09} The data is described with the hexadecimal code. Defines the font for the download characters of alphanumeric characters. · "s" denotes the number of bytes in the vertical direction. · "n" denotes a start character code, and m denotes an end character code. When defining only one character, n should be equal to m (n = m). · Definable character codes are ASCII codes, totally 95 characters ranging from <20>H to <7E>H. · "a" denotes the numberof dots in the horizontal direction to be derection to be defined. · "Dn" is the data to be defined and denotes a pattern corresponding to "a" dot in the horizontal direction from the left end. The right remaining pattern is filled with space. · Once the download characters are defined, they remain effective until redefinition, execution of ESC @, execution of GS *, or power -off. 30 CITIZEN CBM-230/231 User's Manual [Example] For the Font A 31 CITIZEN CBM-230/231 User's Manual For the Font B 32 CITIZEN CBM-230/231 User's Manual (8) Specifying the bit Image (ESC * m n1 n2 D1 ~ Dn) Code : [1B]h + [2A]h + m + n1 + n2 + Dn * {m= Bit image mode (refer to the table below)} {0 n1 FF} {0 n2 02} The data is described with the hexadecimal code. Prints the data in the form of bit image in accodance with the bit image mode specified by "m". [. . . ] · Effective only when this is entered at the beginning of the line. · CBM-231 only. 51 CITIZEN CBM-230/231 User's Manual 10. Character Code Table 10. 1 International 52 CITIZEN CBM-230/231 User's Manual 10. 2 International Character Code Table 53 CITIZEN CBM-230/231 User's Manual Appendix 1. PRECAUTIONS AND MAINTENANCE 1. 1 Precaution for Handling the Printer Mechanism 1. [. . . ]