User manual CITIZEN CBM-262

[. . . ] User's Manual LINE THERMAL PRINTER MODEL CBM-262 Declaration of Conformity Manufacturer's Name : Japan CBM Corporation Manufacturer's Address : CBM Bldg. , 5-68-10, Nakano, Nakano-ku Tokyo, 164-0001, Japan Declare the Product Product Name Model Number(s) Line Thermal Printer CBM-262 Series (CBM-262-R, CBM-262-P) (S. No. 1001001 - ) Conform to the following Standards LVD EMC :EN60950 :EN55022 :EN50082-1 :IEC801-2 :IEC801-3 :IEC801-4 :1992+A1+A2:1993 :1995 Class B :1992 :1991 4KV CD, 8KV AD :1984 3V/m, 27MHz-500MHz :1988 0. 5KV (Signal Line) 1KV (AC Mains) Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the Directive 89/336/EEC, 91/263/EEC, 92/31/EEC, 93/68/EEC" Place: Date: Tokyo, Japan April, 1997 Signature: Full Name: Mikio Moriya Position: General Manager R&D Department European Contact: Norco Declaration AB Box 7146 S-250 07 Helsingborg. Sweden This declaration is applied only for 230V model. Cautions 1. Please read this user's manual thoroughly before attempting to use this printer. [. . . ] · Download characters and a download bit image (GS *) cannot be defined at the same time. · The initial value is "n0 = 0". 7 57 Chapter 7 Print Control Codes (14) Defining download characters (ESC & s n m a (D1 D2~Dn)) Code: [1B] h + [26] h + s + n + m + a + Dn * (s = 03) (20 n 7E) (20 m 7E) (In the case of Font A, (0 a 0C) (In the case of Font B, (0 a 09) Data are expressed in Hex code. This command defines download alphanumeric characters. · s indicates the number of bytes in the vertical direction. · n indicates the starting character code and m indicates the end character code. If only one character is defined, n is made equal to m. · Definable character codes are within the range (20) H ~ (7E) H of ASCII code. A total of 95 characters can be defined. · a indicates the number of horizontal dots that are defined. · Dn are the defining data and indicate the pattern of "a" dots from the left end in the horizontal direction. The pattern remaining on the right end is filled with spaces. · Once it is defined, a download character remains valid until it is redefined, until ESC @ is executed, until GS * is executed or until the power is switched OFF. · It can be known whether characters are downloaded or not by executing ESC v. (In the case of Serial only. ) 7 58 Input Data Format Example · In the case of Font A 12 Dots p1 p4 p7 p34 MSB 24 Dots p2 p5 p35 LSB p3 p6 p36 7 p1=<OF>H p2=<03>H p3=<00>H p4=<30>H p5=<80>H p6=<C0>H p7=<40>H p8=<40>H p9=<20>H . . . . . . 59 Chapter 7 Print Control Codes · In the case of Font B 9 Dots d1 d4 d7 d25 MSB 24 Dots d2 d5 d26 d3 d6 d27 LSB 7 d1 = <03>H d2 = <FF>H d3 = <FF>H d4 = <01>H d5 = <00>H d6 = <20>H d7 = <02>H d8 = <00>H d9 = <10>H . . . . . . 60 Input Data Format (15) Specifying a bit image (ESC * m n1 n2 D1~Dn) Code: [1B] h + [2A] h + m + n1 + n2 + Dn * (m = Bit Image Mode (See the following table. ) (0 n1 FF) (0 n2 03) Data are expressed in Hex code. Data are printed in a bit image in accordance with the Bit Image mode specified by m. · The number of dots printed in the horizontal direction is divided by 256, with n2 being the product and n1 the remainder. · The total number of dots printed as the bit image is n1 + (256 x n2). · If bit image data which exceed the space of one line are input, the portion of data that runs over the end is dropped. · Bit image data (Dn) are specified by "1" in printed bits and by "0" in nonprinted bits. · The Bit Image mode is as shown in the following table. [. . . ] · n indicates the number of dots of a fine bar in the horizontal direction. · The initial value of the horizontal size is "n = 3". (68) Specifying and Clearing smoothing (GS b n) Code: [1D] h + [62] h + n Data are expressed in Hex code. This command specifies or clears smoothing. · In n, the least significant bit (n0) only is valid. [. . . ]