User manual CITIZEN CBM-910

[. . . ] DOT MATRIX PRINTER MODEL CBM-910 CBM-910 User's Manual Declaration of Conformity Manufacturer's Name : Manufacturer's Address : Japan CBM Corporation CBM Bldg. , 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan Declare the Product Product Name : Model Number (s) : Dot Matrix Printer CBM-910 Series (CBM-910R, CBM-910P) (S. NO. 0090001 ) Conform to the following Standards LVD : EMC : EN60950 EN55022 EN61000-3-2 EN61000-3-3 EN55024 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-8 EN61000-4-11 :A4:1997 :1998 Class A :1995+A1:1998+A2:1998 :1996 :1998 :1995 ±4KV CD, ±8KV AD :1996 4. 5V/m, 80MH-1000MHz AM 1KHz 80% :1995 ±1. 0KV (AC Mains), ±0. 5KV (Signal Lines) :1 9 9 6 ± 1 K V (N o rm al m o d e), ± 2 K V (C o m m o n m o d e) :1996 3V, 0. 15MHz-80MHz AM 1KHz 80% :1993 50Hz, 3A/m :1994 0%, 5000ms/ 70%, 500ms/ 0%, 10ms Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC" Place : Tokyo, Japan Date : September, 1995 Signature: Full Name : Mikio Moriya Position : General Manager R & D Department Europe Contact : Norco Declaration AB Box 7146 S-250 07 Helsingborg, Sweden This declaration is applied only for 230V model. CITIZEN CBM-910 User's Manual IMPORTANT SAFETY INSTRUCTIONS * Read all of these instructions and save them for later reference. * Follow all warnings and instructions marked on the product. * Unplug this product from the wall outlet before cleaning. * Do not place this product on an unstable cart, stand of table. [. . . ] 6) GND Signal ground for the circuit. CITIZEN 19 CBM-910 User's Manual (2) Data configuration (1) Start bit (1 bit) (2) Data bit (7 or 8 bit) (3) Stop bit (more than 1) CITIZEN 20 CBM-910 User's Manual 6. 4 Electrical Characteristics (1) RS-232C I/O Signals (RD / TD / DTR) Input (RD / TD) Mark = (-8V): Space = (+8V): Output (DTR) Mark = (-8V): Space = (+8V): stop bit start bit for Busy for Ready (2) TTL Circuit Input (RESET) [HOST] [CBM-910] Set to low when reset [HC04 or equivalent] CITIZEN 21 CBM-910 User's Manual 6. 5 Error Detection * Communication error Parity Error When parity nonconformity heaving been detected out of odd-even parity checking conducted when parity check is assigned. Framing Error When space state is detected on detection of stop bit. Overrun Error When next following data is transferred to receiving buffer register regardless of presence of data in that receiving buffer register. On occurrence of the above error, convert data at the time of occurrence into ` ' (7FH) to print it out. RECEIVING CONTROL AND BUFFERING The CBM-910 controls, on receipt of print data, receiving (DTR Control) in one-word unit. If the host disregards DTR and carries out data transmission at this time, over-run of receiving data may be resulted. This state should be avoided on the host's responsibility. (The data discharging type host cannot follow this. ) This is applicable when the host adopts a double buffer type transmitter. CITIZEN 22 CBM-910 User's Manual 7. DIP SWITCH SETTING 7. 1 Serial Interface Type Function Character CR Bit Length Parity Conditions OFF International CR disregarded 8 bits Provided Odd ON CR + LF 7 bits Not provided Even Factory Setting OFF OFF OFF ON OFF Switch No. 1 2 3 4 5 Baud Rate (bps) Selection Switch No. 6 7 1200 OFF OFF 2400 ON OFF 4800 OFF ON *Factory setting is 4800 bps. 9600 ON ON 7. 2 Parallel Interface Type Function Character CR OFF International CR disregarded ON CR + LF Factory Setting OFF OFF Switch No. 1 2 CITIZEN 23 CBM-910 User's Manual 8. PRINT CONTROL FUNCTION 8. 1 List of Control Codes Symbol LF CR SI SO US RS CAN DC2 DC1 ESC + "B" ESC + "R" ESC + "/" ESC + "!" ESC + "&" ESC + "%" ESC + "K" FS + "W" + 1 FS + "W" + 0 Code (Hexadecimal) 0A 0D 0F 0E 1F 1E 18 12 11 1B/42 1B/52 1B/2F 1B/21 1B/26 1B/25 1B/4B 1C/57/1 1C/57/0 Function Line feed performed after printing. × 4 enlarged letters cancelled. CITIZEN 24 CBM-910 User's Manual 8. 2 Input Data Format (1) Command for line feed after printing (CR / LF) With CR (0DH)/ LF (0AH) codes input, data in the print buffer are printed. Without data in the print buffer, only line feed is performed. This command is disregarded when the buffer is full. EX) 24-Column Model: [Receiving data] 123456789012345678901234567890 123456789012345678901234567890 123456789012345678901234567890 <Result of printing> 1. Dip Switch Setting at CR = CR+LF 123456789012345678901234 CR CR CR LF LF LF CR CR LF SPACE 123456789012345678901234 SPACE SPACE 123456789012345678901234 SPACE SPACE SPACE Head stop position 2. Dip Switch Setting at CR = disregarded 123456789012345678901234 123456789012345678901234 123456789012345678901234 SPACE Head stop position CITIZEN 25 CBM-910 User's Manual (2) SI / SO and US / RS Commands SI / SO codes function in the same manner as US / RS as long as 8-bit data are assigned (serial communication data bit length), which, however, are divided, under 7-bit assignment, into SI (20H~7FH characters) print assignment and SO (A0H~FFH characters) print assignment functions. Standard letter assignment (SI / US) command: With SI (0FH)/ US (1FH) codes input, lateral enlargement is cancelled and the data following are printed in standard letters. This command can cancel only lateral enlargement, which dose not apply to x 4 enlargement. [. . . ] In solchen Fällen sofort den Netzschalter ausschalten und das restliche Papier vorsichtig nach oben herausziehen. Papierhalter CITIZEN 49 CBM-910 User's Manual 4. 5 Selbstdruckfunktion (1) Testdrucken Wenn der Netzschalter bei gedrückt gehaltener Zeilenvorschubtaste (LF) eingeschaltet wird, druckt der Drucker den gesamten verwendbaren Zeichenvorrat aus. Dabei ist die SEL-Lampe erloschen und ein BUSY-Signal wird ausgegeben. Nach Ende des Ausdruckens ist wieder normaler Betrieb möglich. (2) Ausdrucken der DIP-Schalter-Statusdaten Wenn der Netzschalter bei gedrückt gehaltenen LF- und SEL-Tasten eingeschaltet wird, druckt der Drucker den Status der DIP-Schalter- und Übertragungsmethode-Einstellungen aus (einschließlich der Details für serielle Übertragung). [. . . ]