User manual CITIZEN CBM1000

[. . . ] Declaration of Conformity Manufacturer's Name : Japan CBM Corporation Manufacturer's Address : CBM Bldg. , 5-68-10, Nakano, Nakano-ku Tokyo, 164-0001, Japan Declare the Product Product Name Model Number(s) Line Thermal Printer CBM1000 Series (CBM1000RF/PF) (S. No. 9990001 - ) Conform to the following Standards LVD : EN60950 : A11: 1997 EMC : EN55022 : 1998 Class A : EN61000-3-2 : 1995 : EN61000-3-3 : 1995 : EN55024 : 1998 : EN61000-4-2 : 1995 ±4KV CD, ±8 KV AD : EN61000-4-3 : 1995 3 V/m, 80 MHz-1000 MHz AM 1 KHz 80 % : EN61000-4-4 : 1995 ±1. 0 KV(AC Mains), ±0. 5 KV(Signal Lines) : EN61000-4-5 : 1995 1 KV Normal mode, 2 KV Common mode : EN61000-4-6 : 1996 3 V, 0. 15 MHz-80 MHz AM 1 KHz 80 % : EN61000-4-8 : 1993 50 Hz, 3 A/m(Out of scope) : EN61000-4-11 : 1994 10ms/95%, 500ms/30%, 5000ms/100% Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/ 23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC" Place Date Tokyo, Japan August 1999 Full Name : Mikio Moriya Position : General Manager R & D Department European Contact : Norco Declaration AB Box 7146 S-250 07 Helsingborg Sweden Signature Warning : This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This declaration is applied only for 230 V model. --i-- IMPORTANT SAFETY INSTRUCTIONS · Read all of these instructions and save them for future reference. · Follow all warnings and instructions marked on the product. [. . . ] n [Function] [Code] [Range] Specifying the character size <1D>H<21>H<n> 0 1 1 [Outline] n 255, where: 8, 8 vertical magnification horizontal magnification Specifies the character size (Vertical and horizontal magnification). Bit 0 1 2 3 4 5 6 7 Function Value Hex. Number Decimal Number Refer to Table 2, "Vertical Magnification". Vertical magnification specification Horizontal magnification specification Refer to Table 1, "Horizontal Magnification". Table 1 Horizontal Magnification Hex. Decimal 00 0 10 16 20 32 30 48 40 64 50 80 60 96 70 112 Magnification 1 ×(Standard) 2 ×(Double width) 3× 4× 5× 6× 7× 8× Table 2 Vertical Magnification Hex. Decimal 00 0 01 1 02 2 03 3 04 4 05 5 06 6 07 Magnification 1 ×(Standard) 2 ×(Double height) 3× 4× 5× 6× 7× 8× 7 [Caution] · This command works for all ANK characters except for HRI characters. · This command is ignored if either the vertical magnification or horizontal magnification is out of the defined range. · In STANDARD MODE, the vertical direction is defined as the paper feed direction, and the horizontal direction is defined as the direction perpendicular to the paper feed. These definitions are, therefore, interchanged when 90 -right-turned characters are specified. · In PAGE MODE, the vertical direction means the top-bottom direction of each character. The horizontal direction means the side-to-side direction of each character. -- 94 -- · If characters of different vertical magnification are contained in a line, the baseline of each character is lined up. · Horizontal and vertical magnification can also be specified/ canceled by ESC !. command, whichever is handled last, becomes effective. [Default] [See Also] n=0 ESC ! -- 95 -- GS $ nL nH [Function] [Code] [Range] Specifying the absolute vertical position of characters in PAGE MODE <1D>H<24>H<nL><nH> 0 0 [Outline] nL nH 255 255 This command is used in PAGE MODE to specify the vertical position of characters at the data mapping start position as an absolute value measured from the start point. The vertical position of a character at the next data mapping start position will be at a point [(nL + nH × 256) × basic calculation pitch] inches away from the start point. · This command is ignored when PAGE MODE is not selected. · Any specification of absolute vertical position out of the print area is ignored. · The horizontal position of a character at the data mapping start position is not moved. · The start point used as the reference is specified by ESC T. · Depending on the start point specified by ESC T, this command acts as follows: (1) If the start point is the top left or bottom right, the command specifies the absolute position in the paper feed direction (The character's top-bottom direction), using the vertical basic calculation pitch (y). (2) If the start point is the top right or bottom left, the command specifies the absolute position in the direction perpendicular to the paper feed (The character's top-bottom direction) using the horizontal basic calculation pitch (x). · The basic calculation pitch is set by GS P. · Fractions resulting from calculations are corrected with the minimum pitch of the mechanism, and the remainder is omitted. [Caution] [See Also] ESC $, ESC T, ESC W, ESC \, GS P, GS \ -- 96 -- GS * n1 n2 [ d ] n1×n2×8 Defining the download bit image <1D>H<2A>H<n1><n2> [< d >] n1 × n2 × 8 1 1 0 n1 n2 d 255 48 1536 255 [Function] [Code] [Range] n1 × n2 [Outline] Defines download bit images of the number of dots specified by n1 and n2. · The numbers of dots are n1 × 8 in horizontal direction and n2 × 8 in vertical direction. [. . . ] Wenn die Pulsbreite des Signals im Leerzeichenzustand 1 ms oder länger beträgt, wird ein Rücksetzungssignal übertragen. -- 206 -- (6) FG Hierbei handelt es sich um ein Massesignal. (7) GND Hierbei handelt es sich um die gemeinsame Erde von Schaltkreisen. 7. 3. 2 Fehlererkennung Dieser Drucker kann Paritätsfehler, DÜ-Blockfehler und Überlauffehler erkennen. Wenn ein Fehler erkannt wird, werden die fehlerhaften Daten im Pufferspeicher als "?" gespeichert. (1) DÜ-Blockfehler Wenn ein Leerzeichenzustand zum Zeitpunkt einer Stoppbiterkennung erkannt wird, ist ein Fehler aufgetreten. [. . . ]