User manual CITIZEN CBM1000 TYPE II

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CITIZEN CBM1000 TYPE II. We hope that this CITIZEN CBM1000 TYPE II user guide will be useful to you.

Lastmanuals help download the user guide CITIZEN CBM1000 TYPE II.


Mode d'emploi CITIZEN CBM1000 TYPE II
Download
Manual abstract: user guide CITIZEN CBM1000 TYPE II

Detailed instructions for use are in the User's Guide.

[. . . ] This printer conforms to the following Standards: This declaration is applied only for 230V model. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. [. . . ] Allow it to cool off before launching maintenance work. The CBM1000 Type II is a compact thermal line printer designed for use with a broad array of terminal equipment including data, POS, and kitchen terminals. With extensive features, it can be used in a wide range of applications. To obtain the best results from the CBM 1000 Type II printer, please read the instructions this manual thoroughly. Supply/replace paper rolls by simply dropping a paper roll into the printer and closing the cover. Greatly facilitates paper handling and head cleaning. G Ease of paper threading and head cleaning. Allows printer installation and use anywhere with few restrictions. Protects foreign matter or liquid from entering the printer. Select between an easy-to-handle, built-in power supply type and lightweight flat AC adapter type. G Can use 58 mm wide paper rolls by employing the supplied partition. When unpacking the printer, confirm that the following are provided: Printer Partition AC power cord (not supplied with Type D) Do not use the printer in an environment where condensation can occur. If condensation forms, leave the power off until it completely evaporates. Fasten the ground wire to the ground connector on the printer with a screw. Do not connect any other device than the specified drawer (Solenoid) to the drawer kick-out connector. (Do not connect a telephone line either. Function Frame Ground FG DRAWER 1 Drawer 1 drive signal DRSW Drawer switch input VDR Drawer drive power supply DRAWER 2 Drawer 2 drive signal GND Common ground on circuits 5 V, "H"=3 to 5 V (3) DRSW signal DRSW signal status can be tested with the DLE+EOT, GS+a, or GS+r command or at pin 34 on the parallel interface port. A solenoid used for the drawer should be of 24 or more. The output current should be kept at 1 A or less; otherwise, breakdown or burning could occur. Placing your hands on both sides of the printer cover, open it until it comes to a stop. Check the winding direction of the paper roll, and then place it into the paper roll holder correctly. 5 cm out of the case of the printer, close the printer cover. [. . . ] Asynchronous 4800, 9600, 19200 or 38400 bps (User selectable) 1 bit 7 or 8 bits (User selectable) Odd, even, or none (User selectable) 1 bit or more DTR/DSR or XON/XOFF control (User selectable) 1 2 3 4 6 7 20 25 Signal name FG TD RD RTS DSR GND DTR INIT I/O Output Input Output Input Output Input Function Grounding for safety (Case ground) Transferred data Received data Same as DTR Data set ready or reset (Selected with the DIP switches) Ground for signals (Common ground on the circuit) Printer Busy signal Reset (Selected with the DIP switches) While data is not being transferred, be sure to maintain the received data in a mark state. (2) DSR If the DTR/SDR control is selected, the host sends data to the printer after it confirms that the DSR line is at space. if the XON/XOFF control is selected , the host sends data to the printer by ignoring the DSR signal status. (3) INIT This signal can be used as a reset signal after switching the DIP switches. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CITIZEN CBM1000 TYPE II

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CITIZEN CBM1000 TYPE II will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag