User manual CITIZEN CD-S500

[. . . ] 28 Operation when the cover is opened and closed . CE marking shows conformity to the following criteria and provisions: Low Voltage Directive (73/23/EEC)/EN60950-1 EMC Directive (89/336/EEC)/EN55022, EN55024, EN61000-3-2 & EN61000-3-3 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] Referring to the following table, set it at a location suited to the usage environment by moving it to the left and right while pushing the concave part of the center of the sensor with your finger. (When shipped from the factory, it is set at 24mm. ) Paper near end sensor When installed vertically and wall hung The remaining roll paper (external diameter of the roll paper) differs greatly according to the type of roll paper used. When the sensor has detected the remaining roll paper during printing, the printer stops printing after it has printed all the data that it had received. If you are using a model with parallel (IEEE1284) interface specifications, you can select sensor enabled/disabled in Soft SW Setting Mode. If you are using a model with serial (RS232C) interface specifications, it is always enabled. The printing dot line columns are changed as follows by setting the "Paper Width" of the roll paper used, the "Number of col. Font Select 99 dots 40/33 79 dots 99 dots 42/35 79 dots Space between Printing line characters columns 3 dots 3 dots 2 dots 2 dots 33 columns 40 columns 35 columns 42 columns Full columns 400 dots 386 dots 42/35 are selected: 386 dots Paper feed direction Font Select 99 dots 40/33 79 dots 99 dots 42/35 79 dots Space between Printing line characters columns 3 dots 3 dots 2 dots 2 dots 30 columns 36 columns 32 columns 40 columns Full columns 42/35 are selected: 360 dots Right offset: 40 dots Paper feed direction Font Select 99 dots 40/33 79 dots 99 dots 42/35 79 dots Space between Printing line characters columns 3 dots 3 dots 2 dots 2 dots 25 columns 30 columns 27 columns 33 columns Full columns 300 dots 298 dots 42/35 are selected: 298 dots Right offset: 100 dots Paper feed direction Insert your fingers into the dents at opposite ends of the front cover to open it with both hands. Until a click is heard so that the ribbon is between the paper cut bar and the print head cover. If it difficult to insert, turn the ribbon cassette knob again. Paper cut bar Print head cover Close the front cover. caution Be very careful not to let your hands touch the print head cover when replacing the ribbon cassette. When the print head has become heated, there is a danger of it burning your hand. The following are the types of roll paper that can be used by this printer. Types: 1P roll paper 2P copy roll paper (1 original + 1 copy) 3P copy roll paper (1 original + 2 copies) (2P and 3P copy roll paper are only usable on models equipped with auto cutter and rewinder. 20mm (total thickness) But the total thickness that can be cut is from 0. Pull the rear cover open lever towards The roll paper you are using is 69. Change the paper width by changing the value set as the width using the Soft SW Setting Mode. When setting the roll paper, be careful not to cut your hand on the edge of the paper. Place the roll paper and pull the end Of the roll paper directly towards you as shown in the figure. Hold the center of the roll paper to pull it as straight as possible so that one of the sides of the paper does not slacken. Firmly close the rear cover until you hear a click. [. . . ] If you cannot turn the knob, the ribbon may be jammed inside the cassette. If the situation does not improve, replace it with a new ribbon cassette. The paper is not cut Check to make sure that the rear cover and front cover are closed. If the paper still cannot be cut after you have closed the cover, notify the dealer where you purchased the printer or service personnel. [. . . ]