User manual CITIZEN CT-S4000DCL

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CITIZEN CT-S4000DCL. We hope that this CITIZEN CT-S4000DCL user guide will be useful to you.

Lastmanuals help download the user guide CITIZEN CT-S4000DCL.


Mode d'emploi CITIZEN CT-S4000DCL
Download

You may also download the following manuals related to this product:

   CITIZEN CT-S4000DCL AUTRE NOTICE (609 ko)

Manual abstract: user guide CITIZEN CT-S4000DCL

Detailed instructions for use are in the User's Guide.

[. . . ] This printer conforms to the following Standards: This declaration is applied only for 230V model. IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference. [. . . ] when using in horizontal setting , avoid cutting full. Otherwise, the cut paper may drop into the cutter and may result in double cutting and narrow pieces of paper. At the time of shipment, this partition is not installed. Insert the partition into the slot and align it with the scale inside of the printer which meets the width of the paper roll used. 5mm wide paper roll, set the partition by using the accessory screw. When using 112 paper roll, the partition is not used. As for the setting of the serial interface, it gives priority to the setting of the memory switch rather than the DIP switch as the factory default. Consult with the dealer where the printer was purchased when the change of the DIP switch setting is necessary. Function Communication condition 1 setting method 2 Hand shake 3 Bit length 4 Parity check 5 Parity selection 6 Baud rate selection 7 ON DIP switch setting OFF Memory switch setting DTR/DSR 8 bits None Odd parity 38400, 57600 and 115200 bps can also be selected by a command, etc. Lightly push in the paper near-end sensor unit. Move the paper near-end sensor unit to the right and left while keeping to press it. The position to be set varies in accordance with the setting of the printer, horizontal or vertical, or diameter of the paper roll as shown in the following figure. Paper remaining differs by the type of paper roll used. The external diameter of the paper roll is only for reference. When a paper end error is detected incorrectly during using a paper roll with a honeycomb type core, move the sensor position to the larger number. Insert a paper roll with its print area facing down as shown in the figure and pull out the paper end straightforward several cm (or inches) out of the printer. Firmly close the printer cover until a click can be heard. Always use the specified types of paper roll. confirm that the paper roll is set correctly. When the paper is skewed and not extended straightforward from under the printer cover, open the printer cover and adjust the paper correctly. When the printer cover is opened after setting the paper, be sure to pull the paper straightforward several cm (or inches) out of the printer, and then close the printer cover. When closing the printer cover, press on the center part of the cover to close it firmly. [. . . ] Otherwise proper LED light color will not be displayed while touching. 4 Perform Paper Measuring operation When the FEED button is pressed , label is fed and paper measuring is carried. If the FEED button is presed during the paper measuring, the result will be printed out as follows, and the printer memory switch will be initialized. When full-cutting the label paper with the printer installed horizontally, Be sure that the guide plate is mounted on the paper exit of the printer cover. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CITIZEN CT-S4000DCL

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CITIZEN CT-S4000DCL will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag