User manual CITIZEN CX-32N

[. . . ] * Do not place this product on an unstable cart, stand of table. The product may fall, causing serious damage to the product. * Slots and openings on the cabinet and the back or bottom are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. [. . . ] 5 CITIZEN 10 iDP3540/3541 User's Manual 6. 4 Loading and Changing the Paper 6. 4. 1 Using Paper Roll (iDP3540F, 3541) 1) 2) 3) 4) Cut the paper in right angle to its longitudinal center line as shown in Fig. Insert the paper into insertion inlet on the rear side of printer. Turn on the power switch and feed the paper by pushing the LF switch. When the printing paper comes out of the clearance (paper cutter part) on the printer cover, fix the paper by means of paper holder, then set in on the main unit. Fig. 6 CITIZEN 11 iDP3540/3541 User's Manual 6. 4. 2 Using Fan-Fold Paper (iDP3540P) 1) 2) 3) 4) Remove the printer cover Set the imprint face of the paper downward and put into the paper entrance. If necessary to adjust the sprocket-wheel's position, free the wheels using the lever on both sides. Slide them to the appropriate position, and lock them back. Hook some of the paper's perforations on the sprockets and forward the paper into the printer mechanism by pulling and turning the paper-feed knob until the paper's tip reaches the platen. Fig. 8 6. 5 Setting / Removing the Paper Cover and Stacker 1) 2) Setting and removing the paper cover and the stacker as shown in Fig. 9, 10. Capacity of stacker The maximum size of fun-fold paper sheaf which can be stored in this stacker is 3 to 3. 5(W) × 6(H) × 1. 6(D) inches. Fig. 10 CITIZEN 12 iDP3540/3541 User's Manual 6. 6 Self Test Printing Your printer has a built in self print function for purpose of checking print operation without the need for any other external device. New data should be input when this signal is "LOW". (Positive logic) * FAULT : When your printer is in an alarm state, this signal is "LOW". At this time, all control circuits of your printer are interrupted. (Negative logic) Note: An alarm condition occurs when the timing of the print head movement sensor is abnormal. * ACK : c) Power Source * "H" Level * GND * FRAME GND : H level out put for TTL level : The common circuit ground. : Connect the shield of interface cable to this. CITIZEN 15 iDP3540/3541 User's Manual 8. 3. 2 Electrical Characteristics a) Input Signal Level All input signals are TTL level. b) Output Signal Level "HIGH" level . . . . 0. 4V Max. Input / Output Conditions All of the input signals are pulled up by 3. 3K ohms. [Printer Side] [Host Side] 7406 or equivalent All of the output signals are pulled up by 3. 3K ohms. 7406 or equivalent CITIZEN 16 iDP3540/3541 User's Manual 8. 3. 3 Timing Chart a) Data Input and Print Timing 8. 3. 4 Data Receiving Control Your printer is able to receive data sent from the host side when the BUSY signal is LOW, but unable to receive when the BUSY signal is HIGH. 8. 3. 5 Buffering 1) N Type Your printer is provided with a two line input buffer. 2) B Type Your printer is provided with a 7Kbyte input buffer. [. . . ] And drive pulse duration is fixed at 200 ms ON + 200 ms OFF. This command is performed when printer receive it. Remarks: First drawer and second drawer cannot be driven at the same time. CITIZEN 37 iDP3540/3541 User's Manual 13. Initial Setting Followings are automatically set after Power-on. [. . . ]