User manual CITIZEN DCS-950G D-VIEWCAM

[. . . ] D-Link D-ViewCam Central Management Software for SecuriCam Manual Version 1. 10 Building Networks for People Contents A. D-ViewCam Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-ViewCam Main Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. 1. [. . . ] (2) For other D-Link models, it takes 20 seconds for the camera to automatically reconnect. 8. 3. Cycling "Schedule Recording" Step1. Step2. Select the Image icon for the Image Setting Click to select a Schedule Recording Type Step3. Schedule a Weekly Setting Click the Schedule Setting button. Select the time period for which you want to schedule a recording. The activated block will turn pink. Step4. deactivate it. Edit a Schedule To cancel or modify a schedule setting, click the pink block to Step5. Run schedule recording automatically Schedule recording will start immediately after click OK in Weekly Setting and Image setting window, but the recording indicator in Monitor program will be activated only after re-login. NoteWeekly setting is a cycling setting which is automatically applied to the following week, with each block being equal to 1 hour. 33 V1. 10 8. 4. Image Quality Step1. Step2. Select the Image icon for Image Quality. Quality Configuration You can adjust the contrast, hue, brightness, saturation and compression rat from this window; user may drag the scroll bar to right or left direction for your viewing preference and get real time quality by clicking Save button, then all the above setting will be effective automatically. If click Default button, then all the above setting will be restored to default. Note The ranges of parameters are model dependent. It may take longer (roughly 20 seconds) to reconnect device automatically after configuration for some models. If an error message pops up, please check if any related device is unable to connect due to the information described in Error Message window. Solve the problem, and then go back to Camera Setting button to configure this camera again. 8. 5. Configuring Preset Point (Support Pan/Tilt models only) Step1. Step2. Select PT Image icon for Preset Setting. Add Preset Point Use the PT control interface to adjust the angel of camera, choose a number in "Preset Location" field, and enter a name of this point in "Preset Name" text box. Step3. Save Preset Point Click Save and the newly added preset name will show up in the "Preset Location" field (you can also add other preset points in the same way) Step4. Remove Preset Point Select the preset location and click Remove. 34 V1. 10 8. 6. Motion Detection 8. 6. 1. G900. Build-in Motion Detection This function is applicable to DCS-900, 900W, and Step1. Configure Motion Detection Select the Image icon to be configured. Click Detection button from the Manu Bar. A Motion Detection window pops up. Step2. Set Detection Areas A red square follows mouse movement, click to place the red square to the area of motion detection. Step3. Cancel Detection Area Click to deselect a specified area. NoteThe Granularity parameter described in C4. 6 Motion Area Build-in motion detection requires significant processor power. It is advised that no more then 2 Internet cameras have build-in motion detection turned on, or you will have to carefully review hardware performance, and upgrade hardware if necessary. 8. 6. 2. Device Motion Detection Please refer to your camera manual. This function is applicable to camera other than DCS-900, 900W, and G900. 35 V1. 10 8. 7. Sensor Setting Step1. Select Sensor(Digital Input) Select the Sensor icon in System Setup area, then click Sensor Setting button from Manu Bar to open the configuration window. Step2. Edit Location Name. CAMxx-sensor appears by default, you may enter a unique, brief description that identifies the installed location. The maximum Number of characters can be entered is 23. Step3. Save Setting Click OK button to save location data 8. 8. Relay Setting Step1. Select Relay (Digital Output) Select the Relay icon in System Setup area, and then click the Relay Setting button from Menu Bar to open the configuration window. Step2. Edit Location Name. CAMxx-relay appears by default, you may enter a unique, brief but meaningful description that identifies the installed location. Step3. Save Setting Click OK button to save location data 36 V1. 10 8. 9. Alarm Action 8. 9. 1. To Activate Alarm Action ­ Image, Sensor Step1. Start Alarm Action Select the Image icon and click the Alarm button in Manu Bar to bring up the window. Step2. Select "Alarm Activation" Click to select whether you want to trigger alarm in "Disable", "Always", or "Schedule" status. You can change to "Always" to turn it on, or "Schedule" to activate based on the schedule setting. Step3. Step4. The "Holiday" Option Check this option to allow the program records on holiday based on the holiday setup. (Please refer to C4. 2) The " Alarm Interval" Configure the number of seconds between alarms. [. . . ] After I've changed the time or date of my computer system, the D-Link D-ViewCam alarm function does not seem to work anymore? Please exit D-ViewCam then reboot your computer after you've changed your computer system's time and date. The alarm function should go back to normal. 32. What will happen when my hard disk or network storage device is running out of space? When your hard disk's or network storage device's space is approaching 90% full, if you have enabled the Recycle function, the system will automatically delete 20% of the recorded video on your hard disk or network storage device on the first in first out basis. For complete details on how to use this function, please refer to your User's Manual section C4. 4. [. . . ]