User manual CITIZEN IDP-3550

[. . . ] DOT MATRIX PRINTER MODEL iDP3550/3551 User's Manual iDP3550/3551 User's Manual Declaration of Conformity This printer conforms to the following Standards: Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC. LVD : EN60950 EMC : EN55022 Class A EN61000-3-2 EN61000-3-3 EN55024 This declaration is applied only for 230V model. Warning : This is a Class A products. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CITIZEN is a registered trade mark of CITIZEN WATCH CO. , LTD. , Japan CITIZEN es una marca registrada de CITIZEN WATCH CO. , LTD. , Japón ESC/POS and EPSON are a trademark and registered trademark of SEIKO EPSON CORPORATION Star is a registered trademark of Star Micronics Corporation Windows is a registered trademark of Microsoft Corporation CITIZEN iDP3550/3551 User's Manual IMPORTANT SAFETY INSTRUCTIONS · · · · · · Read all of these instructions and save them for future reference. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. [. . . ] PRINT CONTROL FUNCTIONS 14. 1 CBM Mode 14. 1. 1 Command List 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Command FF n FF SO (Note) SI (Note) LF CR DC 1 (Note) DC 2 (Note) DC 3 (Note) CAN ESC * n1 n2 ESC - n ESC 1 ESC 2 ESC 3 ESC C n ESC N n ESC O ESC f 1 ESC t n ESC BEL n1 n2 BEL FS SUB RS ESC P 0 ESC P 1 ESC R n ESC & 0 n1 n2 ESC % n ESC / n ESC DC3 n ESC y n ESC DC2 n1 n2 GS n1 n2 GS / m Function n-line paper feed (CBM1 mode) Form feed (CBM2 mode) Specifying the double width character (CBM mode) Canceling the double width character (CBM mode) Printing and paper feed Printing Initializing the printer (CBM mode) Specifying/Canceling the Inverted character (CBM mode) Specifying the red print (CBM mode) Canceling the print data Specifying the bit image mode Specifying/Canceling the Underline Specifying 1/9-inch line feed width Specifying 2/9-inch line feed width Specifying standard line feed width Setting the page length Specifying the perforation skip Canceling the perforation skip Form feed (Changing the page) Selecting the character code table Setting the external device drive pulse width Driving command A for Drawer-1 Driving command B for Drawer-1 Driving command for Drawer-2 Buzzer-on Full cut Partial cut Selecting the international character set Defining the download character set Specifying/Canceling the download character set Definition the message Printing the message Setting the print lines after paper near end detection Deleting the download character, message, bit image Defining the download bit image Printing the download bit image Code 0CH n 0CH 0EH 0FH 0AH 0DH 11H 12H 13H 18H 1BH 2AH n1 n2 1BH 2DH n 1BH 31H 1BH 32H 1BH 33H 1BH 43H n 1BH 4EH n 1BH 4FH 1BH 66H 01H 1BH 74H n 1BH 07H n1 n2 07H 1CH 1AH 1EH 1BH 50H 00H 1BH 50H 01H 1BH 52H n 1BH 26H 00H n1 n2 1BH 25H n 1BH 2FH n 1BH 13H n 1BH 79H n 1BH 12H n1 n2 1DH 2AH n1 n2 1DH 2FH m Page 44 44 45 45 46 46 46 47 48 48 49 49 50 50 50 51 51 51 53 53 54 54 55 55 55 56 56 56 57 58 58 59 59 60 61 62 Note: Effective when CBM mode is selected with the DIP switch segments 1-9 and 1-10 and CMB1 (OFF) is selected with the DIP switch segment 1-5. If CBM2 (ON) is selected with the DIP switch segment 1-5, the functions of these commands are changed as shown in the table below. 42 CITIZEN iDP3550/3551 User's Manual · CBM2 Mode Command SO SI Code 0EH 0FH 8-bit data selected Specifying the double width character Canceling the double width character Function 7-bit data selected Specifying the shift-out side character Specifying the shift-in side character Page 45 45 Command DC1 DC2 DC3 ESC "C" n Code 11H 12H 13H 1BH 43H n Function Selecting the printer Specifying the red print Deselecting the printer Setting the page length Page 47 47 48 52 14. 1. 2 Description of Items ALL XXXX [Function] Command name [Code] A row of command constituent code is represented by a hexadecimal number with < >H, binary number with < >B, and a decimal number with < >. [ ]k means a repeat count of [Range] Describes an argument value (Setting range) for the command. [Outline] Describes a command function. [Caution] Describes a caution as required. [Default] Describes an initial value for the command when accompanied by an argument. XXX Shows a command. 43 CITIZEN iDP3550/3551 User's Manual Details FF n [Function] n-line paper feed (CBM1 Mode) [Code] <0C>H n 1 n 127 This command feeds the paper by n-lines. If the print [Range] [Outline] buffer contains the data, use of this command feeds the paper by n-lines after printing the data. Setting n = 0 does not feed the paper. FF [Function] Form feed (CBM2 Mode) [Code] <0C>H [Outline] This command searches for the beginning of the next page after printing the data in the print buffer. SO [Function] Specifying the double width character (CBM1 Mode) [Code] <0E>H [Outline] The data following this command is printed doubled in the horizontal direction. Double width characters remain valid until the double width character cancel command is entered, but they are also cancelled after they are printed one line. characters take up two ordinary characters worth of width. Note that the double width 44 CITIZEN iDP3550/3551 User's Manual SO [Function] Specifying the double width character/shift-out side characters (CBM2 Mode) [Code] <0E>H [Outline] The data following this command is printed doubled in the horizontal direction. Double width characters remain valid until the double width character cancel command is entered, but they are also cancelled after they are printed one line. characters take up two ordinary characters worth of width. In the case of a serial interface, if 7-bit data is selected, the shift-out side character is printed. Note that the double width SI [Function] Canceling the double width character (CBM1 Mode) [Code] <0F>H [Outline] This command cancels the double width characters set with SO. command are printed in the ordinary character width. The data following this SI [Function] Canceling the double width character/Specifying the shift-in side characters (CBM2 Mode) [Code] <0F>H [Outline] This command cancels the double width characters set with SO. command are printed in the ordinary character width. The data following this In the case of a serial interface, if 7-bit data is selected, the shift-in side character is printed. 45 CITIZEN iDP3550/3551 User's Manual LF [Function] Printing and paper feed [Code] <0A>H [Outline] If the print buffer contains the data, this command will feed the line after printing. the command only feeds the line. If not, CR [Function] Printing [Code] <0D>H [Outline] This command prints the data. If the DIP switch segment 1-6 is set to OFF, the printer will print the data in the print buffer and feed the paper by one line. If it is set to ON, the print er will print the data in the print buffer and will not feed the paper. DC1 [Function] Initializing the printer (CBM1 Mode) [Code] <11>H [Outline] This command initializes the printer. The settings of the DIP switch segments are not re-read. 46 CITIZEN iDP3550/3551 User's Manual DC1 [Function] Selecting the printer (CBM2 Mode) [Code] <11>H [Outline] This command sets the printer in the selecting status. DC2 [Function] Specifying/Canceling the inverted character (CBM1 Mode) [Code] <12>H [Outline] This command selects/deselects the inverted characters. Otherwise, it is overridden. Enter this command at the Erect and inverted characters cannot DC2 [Function] Specifying the red print (CBM2 Mode) [Code] <12>H [Outline] This command specifies red-color characters. All the characters in one line are printed in When you red by prefixing the print data with this command and sending it to the printer. want to use red characters, use this command for each line. 47 CITIZEN iDP3550/3551 User's Manual DC3 [Function] Specifying the red print (CBM1 Mode) [Code] <13>H [Outline] This command specifies red-color characters. All the characters in one line are printed in When you red by prefixing the print data with this command and sending it to the printer. want to use red characters, use this command for each line. DC3 [Function] Deselecting the printer (CBM2 Mode) [Code] <13>H [Outline] This command sets the printer in the deselecting status in which the printer cannot receive data. To set the printer in the selecting status, use DC1. CAN [Function] Canceling the print data [Code] <18>H [Outline] This command clears the print data in the lines entered prior to this command. 48 CITIZEN iDP3550/3551 User's Manual ESC "" n1 n2 [Function] Specifying the bit image mode [Code] <1B>H <2A>H n1 n2 1 n1 + 256 × n2 230 (for DP650 mechanism) 1 n1 + 256 × n2 280 (for DP652 mechanism) 1 n1 + 256 × n2 360 (for DP654 mechanism) 1 n1 + 256 × n2 400 (for DP657 mechanism) [Range] [Outline] This command allows printing in the bit image mode. horizontal dots will be n1 + 256 × n2. Divide the number of dots printed Therefore, the number of by 256 and assume its quotient to be n2 and remainder to be n1. If the bit image data is entered beyond the dot positions printable in one line, the surplus data will be discarded. Normal data processing is restored after bit image printing. Printing is done in a single direction. ESC "-" n [Function] Specifying/Canceling the underline [Code] <1B>H <2D>H n [Outline] This command selects/deselects an underline. deselected at n = 0. The underline is selected at n = 1 and [Default] n=0 49 CITIZEN iDP3550/3551 User's Manual ESC "1" [Function] Setting the 1/9-inch line feed width (Graphic type) [Code] <1B>H <31>H [Outline] Only effective for Graphic type. [. . . ] OFF · Das Lämpchen SEL/ERROR blinkt in Abständen von 0, 25 Sekunden. · Ein Signalton ist 1 Sekunde lang zu hören. Es wird die Meldung , , Clear in Data in Buffer " vergrößerten roten Zeichen gedruckt. Danach erfolgt ein schneller Zeilenvorschub von fünf Zeilen. Pufferdaten NEIN JA JA 1 Sek. [. . . ]