User manual CITIZEN IDP-562

[. . . ] DOT MATRIX PRINTER MODEL iDP-562 iDP-562 User's Manual Declaration of Conformity Manufacturer's Name : Manufacturer's Address : Japan CBM Corporation : CBM Bldg. , 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan Declare the Product Product Name Model Number (s) Dot Matrix Printer iDP-562 Series (iDP-562RSL2, iDP-562RSL, iDP-562CNL, iDP-562RS, iDP-562CN) (S. NO. 60100000 - ) Conform to the following Standards LVD EMC : EN60950 : EN55022 : EN61000-3-2 : EN61000-3-3 : EN50082-1 : IEC801-2 : IEC801-3 : IEC801-4 :1992+A1+A2:1993 :1994 Class B :1995 :1995 :1992 :1991 4KV CD, 8KV AD :1984 3V/m, 27MHz-500MHz :1988 0. 5KV Signal Line 1KV AC mains Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68EEC" Place: Date: Tokyo, Japan January, 1996 Signature: Full Name : Mikio Moriya Position : General Manager R & D Department Europe Contact : Norco Declaration AB Box 7146 S-250 07 Helsingborg Sweden This declaration is applied only for 230V model. CITIZEN iDP-562 User's Manual IMPORTANT SAFETY INSTRUCTIONS * Read all of these instructions and save them for later reference. * Follow all warnings and instructions marked on the product. * Unplug this product from the wall outlet before cleaning. [. . . ] DSW-1 DSW-2 DSW-3 CR and LF code When CR code comes are valid function. immediately after full When the buffer is blank. *OFF CR code is selected by buffer printing the DSW-2 and 3. *OFF CR code is void *OFF CR code is valid ON CR code is valid ON CR code is void CR code is ignored When LF code comes immediately after full buffer When the buffer is blank. ON LF code is selected by printing the DSW-2 and 3. *OFF LF code is void ON LF code is valid *OFF LF code is valid ON LF code is void It is recommended to set the DIP switches in accordance with your host's output DATA format. DATA Form DATA + CR DATA + LF DATA + CR + LF DATA + LF + CR Foreign character Selection DSW-1 DSW-2 DSW-3 OFF OFF OFF ON OFF OFF DSW-4 DSW-5 DSW-6 DSW-7 DSW-8 SSW *OFF -1 ON DSW-9 DSW-10 Parity check Selection of DATA bit length Selection of Baud Rate USA *OFF *OFF ODD *OFF OFF ON *OFF 9600 1200 *OFF *OFF GERMANY OFF ON EVEN ON OFF 4800 600 OFF ON FRANCE UK ON ON OFF ON No Check *OFF ON *ON *ON 7 bit DATA 8 bit DATA 2400 1200 300 150 ON ON OFF ON NOTE: * Marks are a "Factory Setting". CITIZEN 9 iDP-562 User's Manual 5. 3 Connectors and Signals Signal Pin 1 7 3 20 14 25 17 23 24 Return Line Signal Name FG SG RD DTR FAULT RD DTR Direction of Signal Function Frame GND GND Input DATA BUSY signal ALARM signal Input DATA BUSY signal A: Computer B: Printer RS232C CURRENT LOOP TTL AB Notes: 1. Signal of RS-232C conforms to EIA RS-232C level. Signal of CURRENT LOOP should be restricted within 10 ~ 20 mA. 3 at MARK status when no transfer of DATA. Selection of modes, those are RS-232C, CURRENT LOOP and TTL, can be made by the preset jumper (Please refer to `Setting of Preset Jumper'). Compatible Connector (D-Subconnector): * Printer: 17LE-13250 (AMPHENOL or equivalent) * Cable Side: 17JE-23250 (AMPHENOL or equivalent) 5. 4 Interface Circuit RS-232C Input (RD) Printer side Computer side Equivalent to 232 Output (DTR FAULT) Equivalent to 232 CITIZEN 10 iDP-562 User's Manual 5. 5 Current Loop and TTL 5. 5. 1 Interface Circuit (a) Current Loop Input (RD) Printer side Computer side Output (DTR) Note: Resistance should be set so that Current Loop is restricted within 10 ~ 20 mA. (b) TTL Input (RD) Printer side Computer side Equivalent to 7407 Output (DTR FAULT) Note: Output is open collector. CITIZEN 11 iDP-562 User's Manual 5. 5. 2. Setting of Preset jumper Following function are available by setting preset jumper 1 ~ 6. Please turn off power and remove a bottom case before setting. iDP-562-RSL2 iDP-562-RSL/RS CITIZEN 12 iDP-562 User's Manual Preset jumper Preset Jumper 1 2 3 4 5 Mode CURRENT LOOP TTL × B × B B B B A × B × : Both A and B can be set. RS-232C A A A × A B position A position A B DATA can be transferred at DTR = SPACE (RS-232C / TTL level) DATA can be transferred at DTR = MARK (CURRENT LOOP) DATA can be transferred at DTR = MARK B (RS-232C / TTL level) DATA can be transferred at DTR = SPACE (CURRENT LOOP) At shipping all of preset jumper are set as A. A 6 CITIZEN 13 iDP-562 User's Manual 5. 6 DATA Construction 5. 6. 1 Serial Data format 1. Stop BIT (1 ~ 2 BIT) (1) START BIT At 1 / 2 BIT after (a), signal level is checked out, (b). When signal level is SPACE, START BIT is recognized at this stage. When signal level is MARK, continuous search for START BIT is made for the next bit. DATA BIT + PARITY BIT DATA BIT and PARITY BIT are checked out every 1 / 2 BIT from the half point of START BIT, (b). Signal level of these points (MARK = 1, SPACE = 0) are read as input DATA. [. . . ] Try to select decimal data or hexadecimal data matching to the host computer. CITIZEN 24 iDP-562 User's Manual 6 Paging designation and page length designation ESC(1B) C(43) n Input ESC C (1B, 43) at the top of the line and next input n, which are integers. With this code, the length (number of line) per page can be set, and paging action is started, and the space of three lines are left at the both top and bottom of the page, n should be: 14 n 120 Otherwise, it comes to 66. The paging can be released by ESC O (1B, 4F). 7 Form Feed FF(0C) With this code, paper feed goes on. [. . . ]