User manual CITIZEN PPU-700U BROCHURE

[. . . ] PRINTER PRESENTER UNIT MODEL PPU-700 User's Manual WEEE MARK En Ge Fr Sp It Du Da Por Pol Declaration of Conformity This printer conforms to the following Standards: Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC. LVD : EN60950 EMC : EN55022 EN61000-3-2 EN61000-3-3 EN55024 Class A This declaration is applied only for 230V model. CITIZEN is registered trade mark of CITIZEN WATCH CO. , LTD. , Japan CITIZEN es una marca registrada de CITIZEN WATCH CO. , LTD. , Japón IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference. CAUTION: Use shielded cable for this equipment. Sicherheitshinweis Die Steckdose zum Anschluß dieses Druckers muß nahe dem Gerät angebracht und leicht zugänglich sein. For Uses in Canada This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus, as set out in the radio interference regulations of the Canadian department of communications. [. . . ] (See "4. 8 Removing Cutter Lock". ) G Low voltage error This error occurs when the voltage supplied to the printer is too low. If this error occurs, turn the printer power off immediately. G High voltage error This error occurs when the voltage supplied to the printer is too high. If this error occurs, turn the printer power off immediately. G Presenter error This error occurs when the presenter cannot eject paper or it cannot collect the ejected paper. To clear this error, remove the jammed paper or press the FEED switch. G Black mark detection error This error occurs when the printer cannot detect the black mark. If this error occurs, turn the printer power off and confirm the paper and memory switch setting. -- 39 -- 5. NOTES ON EXTERIOR DESIGN 5. 1 Notes on Paper Exit 1. Use consideration to prevent the ejected paper from entering the gap of the exterior case. Avoid the shape that may obstruct the paper ejected from the presenter unit. Use consideration to design the shape that may prevent entry of dust, drops of water from the outside. Keep a space enough to open the paper guide for maintenance purpose. B A -- 40 -- 7 mm min. Paper width 7 mm min. 63 mm 44. 5 mm In case of 3 mm In case of 10 mm Setting range at opening 58. 5 mm max. 7 mm min. 60 21. 4 mm ~ 3 mm min. 10 mm max. -- 41 -- 58 mm (Paper width) 67 mm (Paper width) 80 mm (Paper width) 82. 5 mm (Paper width) 19. 4 mm 5. 2 Notes on Paper Collection Hole and Collection Path When implementing paper collection, be sure to prepare the paper collection hole as shown below. Be careful to prevent irregularity, burr, etc. Otherwise paper jam may occur. M4 12 50 50 104. 2 9. 5 Paper Collection Hole 40. 5 mm min. 40. 5 mm min. Printer setting position 6. 3 40. 5 Note: Fix at 2 places or more in one side totaling 4 places or more. -- 42 -- 5. 3 Notes on Paper Insertion Path When feeding paper without using optional PHU-3***, set the paper path in the following range. When using a large-diameter paper roll, be sure to provide a shock absorber to prevent shock during rotation of paper roll. 55 ° 15. 5 120 5. 4 PHU-3*** (Paper Feed Unit) Installation Refer to "Appendix-2. PHU-3*** (Paper Feed Unit) Installation". -- 43 -- 74. 5 Ra ng e Pa pe rI ns tio er n Pa th 5. 5 Layout Examples of Control Box Separation of Control Box from Printer allows you to enjoy free layout. PPU-700 Layout Example (1/3) Basic Type Example 1) With board installed separately. PPU-700 Layout Example (2/3) Example 2) With board installed below PPU-700. Example 3) With board installed above PPU-700. PPU-700 Layout Example (3/3) Example 4) With paper holder installed under PPU-700. Example 5) With paper holder installed above PPU-700. -- 44 -- 6. DIP SWITCHES 6. 1 Setting DIP Switches The DIP switch is located on the serial interface board of the printer. DIP switch setting with the printer power on is not valid. [. . . ] Aktivieren des Einstellmodus für Speicher-Switches Führen Sie Papier in den Drucker ein und lassen Sie die Papierabdeckung geöffnet. Schalten Sie den Drucker bei gedrückter Vorschubtaste (FEED), und drücken Sie anschließend zweimal auf die Vorschubtaste. Wenn der Drucker daraufhin die aktuellen Einstellungen der Speicher-Switches usw. ausdruckt, wurde der Einstellmodus erfolgreich aktiviert. [. . . ]