User manual CITIZEN PRODOT 300

[. . . ] 7 Automatic Media Thickness Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Automatic Media Straightening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Left Edge Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Automatic Media Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the product has been dropped or the cabinet has been damaged. If the product exhibits a distinct change in performance, indicating a need for service. 14. This plug is not waterproof - keep it dry 15. The power cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS1362 fuse must be used of the same rating, marked thus. If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i. e. Fuse covers are available from the Parts Department indicated in your user instructions. If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed. A plug with bared flexible cords is hazardous if engaged in a live socket outlet. The end of the flexible cord should be suitably prepared and the correct plug fitted. Where it may be accidentally splashed with water. -9- Parts Identification A B C D E F G H I J K Top Cover Control Panel Parallel Interface Serial Interface Front Rollers Ribbon Cassette Cartridge Printhead Left Adjustable Media Guide Front Table For Media Paper Feed Knob Gap Sensing Pressure Adjustment Switch - 10 - A B C D Tractors (to accept continuous, sprocket fed paper) Power Supply Inlet (to be connected to the mains supply) Power Switch Paper Select Lever Inserting And Replacing The Ribbon Cassette 1. Turn on the printer power switch and then set the printer off-line by pressing the on-line key. Open the top cover and then pull the front roller unit by gripping the centre area of the unit by your forefingers until you hear a click. Then lift it - 11 - up until the unit is positioned on the top of printer as shown above. If necessary, centre the print head by hand 4. Hold the ribbon cartridge with the knob facing upwards and turn the ribbon knob in the direction shown by the arrow to take up any slack in the ribbon. 5. To install the ribbon cartridge, hold it with both hands, with the ribbon facing down as shown in the figure. When you look at the print head you will find a small piece of black plastic on the thin metal sheet of the ribbon guide. Make sure that the ribbon goes under the piece of plastic. Position the ribbon cartridge with the tabs on its case over the slots inside the printer case. [. . . ] Using a fixed length passbook setting will be quicker as the printer does not have to check and determine the length of the passbook before printing starts. Calculation of PB Length for Passbook2 mode. First determine the size of one leaf of the passbook, as shown in the diagram. If this value is in millimetres, convert to inches by dividing by 25. 4 and then multiply by 6 to give the number of lines on a page. - 24 - Here is an example: The length of one page is the distance from the edge of the passbook to the centre line of the opened book, as shown above. In this case, the passbook is 85mm per leaf or page. [. . . ]