User manual CLARION CC-2011E

[. . . ] 5 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Before installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Precautions when using two-sided tape for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Install accessory parts as directed. · When drilling holes in the vehicle for installation of wiring, always use insulated grommets in the holes to protect the wiring. · If holes are drilled in the vehicle to install the camera, or when installing wiring, use silicon sealant to seal any gaps. · Do not damage or scar the camera wiring. · After completing the camera wiring, use cable clamps or insulation tape to bundle the wiring together. · The images produced from the rear-view monitor are inverted right-left in the same way as images seen in the vehicle's rearview mirrors. The image may differ depending on the vehicle type. · Do not use high-pressure car washing devices around the camera. The camera is a high-precision instrument and should not be subjected to high-pressure water stream impacts. · Periodically check the tightness of the installation screws and retighten if necessary. CC-2011E 3 3. SPECIFICATIONS Power source/voltage: Power consumption: Image sensor: Angle of view: Minimum subject illumination: SN ratio: Weight: Dimensions: DC 9 V (±0. 5 V) 120 mA or less 1/4" solid-state color CCD About 130° (horizontal) About 97° (vertical) 3 LUX or less (2 LUX ±1 LUX) 48 dB or more (AGC-OFF) About 72 g (bracket and 0. 5 m cable) 27 (W) × 25 (H) × 28. 3 (D) mm English Note: · Specifications and design are subject to change without notice for further improvement. Package contents 1 1 2 3 4 5 6 7 Camera (with 0. 5 m cable) . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting bracket A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting bracket B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting bracket C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation screws (hex head M3 x 6) . . . . . . . . . Installation screws (pan head M3 x 6) . . . . . . . . Cleaning fluid (for use in preparing surface for 2-sided tape) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Cable holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Cable clamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 Owner's manual & Installation manual . . . . . . . 1 1 1 1 4 2 1 7 3 1 2 3 4 5 6 8 9 7 0 4 CC-2011E 4. OPERATION Operation when using Clarion rear-view camera system The rear-view image is displayed when the transmission is placed into reverse, or when the manual switch is operated. English Troubleshooting The following symptoms are not malfunctions. [. . . ] · Within the first 24 hours after installation, do not expose the installation to moisture (water, rain, mist, snow, etc. ), or subject the installation to strong forces or impacts. · When installation must be performed under conditions of low ambient temperature (20°C or below), use a hair dryer to warm the surface of the bracket where the 2-sided tape is to be applied. · Do not touch the bracket-mounting surface's 2-sided tape, and do not attempt to move or reset the tape after initial application. 6 CC-2011E Installing/Wiring the camera English 2. Install mounting bracket A Using the supplied 2 installation screws (hex head M3 x 6), fasten bracket A to bracket B. [. . . ]