User manual CLARION CDC1255Z INSTALLATION MANUAL

[. . . ] OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS PRODUCTION COMPLIES WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE. 50 KAMITODA, TODA-SHI, SAITAMA-KEN, JAPAN. Y-adapter (Brack) (Brack) (Gray) Ferrite clamp (Horizontal Position) 4. Remove the separator of the cushion rubber that is attached to the installation bracket with bolt and install accordingly. [. . . ] Do not attempt to insert different style magazine into the CD changer even if they fit into the magazine opening. Inserting other manufacturers' magazines or previous Clarion 6 Pack style magazines into the CDC1255z or RDC1255z will cause damage to the mechanism and void the warranty. Label Side One in each slot (6 pieces) 15° 30° 45° 15 ° 3 CAUTIONS ON HANDLING CDs mark. Use only compact discs bearing the Do not play heart-shaped, octagonal, or other specially shaped compact discs. Handling q New discs may have some roughness around the edge. The set may not work or the sound may skip if such discs are used. Use a ball-point pen, etc. , to remove roughness from the edge of the disc. Ball-point pen Roughness q Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These may get caught in the internal mechanism and damage the disc. Storage q Do not expose compact discs to direct sunlight or any heat source. q Do not expose compact discs to excess humidity or dust. q Do not expose compact discs to direct heat from heaters. q Never stick labels on the surface of the compact disc or mark the surface with a pencil or pen. q Never play a compact disc with any cellophane tape or other glue on it or with peeling off marks. If you try to play such a compact disc, you may not be able to get it back out of the CD player or it may damage the CD player. q Always handle the compact disc by the edges. Never touch the surface. Cleaning q To remove fingermarks and dust, use a soft cloth and wipe in a straight line from the center of the compact disc to the circumference. q Do not use any solvents, such as commercially available cleaners, anti-static spray or thinner to clean compact discs. q After using special compact disc cleaner, let the compact disc dry off well before playing it. H <Example of address switch setting> q Setting example 1 Source unit CD changer CeNET wire bound 2 Address switch number 2 CD changer 1 Address switch number 1 Important Important 7 · INSTALLATION OF CONNECTORS CeNET cable Be sure that the CD changer numbers are not the same. Note: Only the provided screws and brackets should be used during installation. Using screws other than those specified will cause damage. 7. Align the unit with the bolts and secure it with the wing nuts. q Setting example 2 Source unit CD changer When the CeNET cable is connected, it must be inserted fully and securely. After connecting, fasten the cable using the cable holder or cable clamp. After connecting, fasten the cables with cable holders, etc. When removing the digital optical fiber cable, rotate it to loosen it and pull it gently while holding the slide cap (a gray color part on the source unit). Do not coil up the digital optical fiber cable with a radius of less than 1" (3 cm). [. . . ] When installed at an angle, change the installation selector lever to a position (H, 45, V) not prone to noise or sound loss. 2. Load the magazine in the direction as shown in the diagram. (3. 3kg) : 10. 6"(Width) × 3. 9" (Height) × 6. 7"(Depth) [268mm(W) × 98mm(H) × 170(D)mm] 2. Remove the magazine when it has been ejected. Installation Procedure Note: When taking out the CD do not let your fingers touch the signal side of the CD. 1. [. . . ]