User manual CLARION DSC920S

[. . . ] INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The DSC920S can easily be damaged by moisture, high temperatures or high humidity. Keep the inside of the car clean and well ventilated. Never subject the DSC920S to strong shocks or open its case. [. . . ] UPDATING : displayed when the receiver is turned on or after a reset. INVLD CH : a channel without a broadcast has been selected. SCAN indication: · Lights when category scan is performed or when preset scan is performed. CAT (category) indication: · Lights when the unit enters the Category selection mode or when category scan is performed. PRESET indication: · Lights when the unit enters the Preset memory mode. BAND indication: · Lights when the band ("SAT1", "SAT2" or "SAT3") is being received in the SAT mode. 4 DSC920S 4. OPERATIONS Turning the power on/off 1. Press the [SAT] button to turn the power on/ off. When the power is turned on, "SAT" is displayed in the Operation status indication and then the display is changed to the channel being received. Press and hold the [a] or [d] for 1 second or longer. The receiver moves to seek channels below or above the current channel and the channel found when either button is released is received. q Seek tuning Only channels that can be received are selected while channels without broadcasts and channels not covered by the contract are automatically skipped. The receiver seeks the next available channel below or above the current channel. The receiver moves to seek channels below or above the current channel. If the channel found when either button is released is available that channel is received. Otherwise, seeking continues until an available channel is found. English Verifying your Sirius ID 1. Press and hold the [SS] button for 1 second or longer to enter the Adjust mode. Press the [a] or [d] to select the "ESN >>". When the unit enters the SIRIUS ID display mode, "ESN>>" is displayed and then the display is changed to the high-order 6 digits of the SIRIUS ID ("012345 z") in the Operation status indication. 3. Press the [z] button to change the low-order 6 digits of the SIRIUS ID ("678901 w"). To display the high-order 6 digits of the SIRIUS ID again, press the [w] button. 4. Press the [a] or [d] button to return the previous mode. Preset memory 3 bands are available for preset memory and 6 channels for each band, a total of 18 channels can be stored in memory. The indication concerning the preset memory is displayed both in the BAND indication for the band being received ("SAT1", "SAT2", or "SAT3") and in the Preset channel indication for the preset number. Press the [w] or [z] button to recall a preset station. Each time the button is pressed, preset stations are recalled in a sequential order. When the [P-M] button is pressed and the Preset memory mode is engaged, preset stations cannot be recalled. When the button is pressed, the sound is muted and reception channel data are displayed in the Operation status indication in the following order. Channel number (for example "CH 051") § abbreviated 8-digit channel name § returned to the original display mode Selecting a band 1. Press the [BAND] button to select a band. BAND indication ("SAT1", "SAT2" or "SAT3") is light in the display. Tuning mode There are two channel selection modes: seek mode and manual mode. [. . . ] If the reception channel is changed, the display changes in the order of channel number § channel name (short) and then the original display mode is resumed. When there is no text information, the indication "--------" will appear on the display. About the scrolling of the displayed text Scrolling is performed once when the title being selected is changed or when the [DISP] button is pressed and held for 1 second or longer. Scrolling is not performed when a channel number, abbreviated channel name or category is displayed. 6 DSC920S Operations English Switching the screen saver 1. Press the [SS] button to switch the screen saver. Each time the button is pressed, the screen saver is switched in the order of OFF § SS1 § SS2 § OFF. If the screen saver is turned on and the button operation is performed, the screen saver mode is released. [. . . ]