User manual CLARION MSS433

[. . . ] · Before installation, disconnect the (­) negative lead from the vehicle's battery. · Use only supplied screws and hardware. Make sure all connections and components are fastened securely. · At the proposed installation sites, make sure there is adequate space to accommodate both MSS433 and the Control Station dimensions. [. . . ] NOTE: Do not connect high level speaker-level wires to these inputs. The MSS433 requires low-level signal inputs only. 1 A/V INPUT 1 (3 -RCA Jacks) Use a triple RCA A/V cable (not supplied) to connect video and stereo audio from the primary video source (e. g. , Clarion CVP9700 VCR, VS718 DVD Player, etc. ) to the MSS433 A/V Selector. See Applications on page 15. 2 A/V INPUT 2 (3 -RCA Jacks) Same as A/V Input 1. Use these jacks to connect a second video source (e. g. , video game console, etc. ) 10 OWNER'S MANUAL/INSTALLATION GUIDE 3 A/V INPUT 3 (3 -RCA Jacks) Same as A/V Input 1. Use these jacks to connect a third video source. 5 POWER INPUT CONNECTOR (4-Pin Molex) Connect the enclosed Molex pigtail to the vehicle's power, ground, and back-up light circuits, (see Figure 3 on page 6). 4 A/V INPUT 4 (3 -RCA Jacks) Same as A/V Input 1. Use these jacks to connect a fourth video source. NOTE: When using a optional Clarion Rear Vision Camera, the video connection must be connected to A/V Input 4 to function properly with the reverse wire. See Figure 6 on page 8 for connection configuration. When +12Vdc is applied to the reverse wire (Pin 4), the MSS433 will automatically override Control Station 1's video selection and switch directly to A/V Input 4. The LED indicator will blink to show that the reverse function is active. The video signal will automatically override any other selection that is being viewed on Monitor 1. When voltage is removed from the reverse wire, the monitor will automatically switch back to the original source selected. 11 SOURCE COMMANDER MSS433 DESCRIPTION OF MSS43. REAR CONNECTORS (CONT'D) +- +- +- 6 7 8 9 0 q w e r Figure 10. The MSS433's A/V Outputs and Power connectors. 6 CONTROL STATION 1 (6 -Pin Connector) The Control Station connected to this port provides control and selection of Zone 1 audio/video sources. The Control Station connected to this port provides control and selection of Zone 3 audio/video sources. 9 A/V OUTPUT 1 (3 -RCA Jacks) Use this output when connecting the MSS433 to an external (PAL/NTSC-compatible type) video monitor for Zone 1. 7 CONTROL STATION 2 (6 -Pin Connector) The Control Station connected to this port provides control and selection of Zone 2 audio/video sources. 8 CONTROL STATION 3 (6 -Pin Connector) 12 0 MONITOR 1 OUTPUT (2 -Pin Connector) OWNER'S MANUAL/INSTALLATION GUIDE Connect to the monitor's +12 V and ground for Zone 1. DESCRIPTION OF CONTROL STATION q A/V OUTPUT 2 (3 -RCA Jacks) Use this output when connecting the MSS433 to an external video monitor for Zone 2. 1 w MONITOR 2 OUTPUT (2 -Pin Connector) Connect to the monitor's +12 V and ground for Zone 2. e A/V OUTPUT 3 (3 -RCA Jacks) Use this output when connecting the MSS433 to an external video monitor for Zone 3. 4 2 3 Figure 11. The Control Station's Power button, source LED indicators, and Source Select buttons. r MONITOR 3 OUTPUT (2 -Pin Connector) Connect to the monitor's +12 V and ground for Zone 3. 1 SOURCE SELECT LEDs When illuminated, each LED indicates which A/V source is selected. Press the SOURCE SELECT button to change source selection and the corresponding LED will illuminate. 13 SOURCE COMMANDER MSS433 2 SOURCE SELECT Button Press the SOURCE SELECT button one or more times to step through the different Audio/Video inputs. Each LED illuminates to confirm the source selected. Press and hold the Power button for 2 to 3 seconds to power down the monitor at each of the Control Stations. 4 Mounting Bezel Outer mounting bezel around each Control Station allows for easy installation. (see page 6 for intallation information). 3 POWER Button When ignition is applied to the MSS433's ignition lead, all control stations are automatically set into the Stand-By mode (no power output from the monitor's power connector). Press the POWER button on any Control Station and the source LED will illuminate and the monitor will power on. NOTE: Control Stations a). If the Ignition is shuts down while the Control Stations are in use, the Control Stations will not automatically turn on when the ignition is activated again. Press the Power button on the Control Station again. [. . . ] No sound from in-dash monitor CCA389 not connected properly. Camera not connected Connect a Clarion Rear Vision properly. Camera to the A/V INPUT 4 video connector. No Power to CAA188 Check power and ground connections to CAA188. Reverse Wire not con- Check for proper connection and nected on CAA188 +12 V on Reverse Wire when camera power supply. [. . . ]