User manual CLARION N.I.C.E. 430

[. . . ] 430 Owner's Manual R00 (USA) Trademarks All brand and product names are trademarks or registered trademarks of their respective companies. Note The information in this manual is subject to change without notice. Table of Contents Precautions and Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v 1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1 Understanding Hardware Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Front Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Back Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This semi-transparent icon is displayed if GPS position is available, and the map has been moved or rotated. It also appears when you scale or tilt the map while Smart Zoom is enabled. Normally N. I. C. E 430 positions the map to keep the GPS position visible somewhere on the map (when North-up orientation is selected), or always at the bottom center of the map (when Track-up orientation is selected). If you manually move the map, it will freeze the map in the new position. To return to the GPS position, use this Follow button. When Smart Zoom is enabled, scaling or tilting the map also stops the automatic zooming or automatic tilting respectively. To reactivate Smart Zoom, tap this button. Tip: In Advanced settings you can set a delay time after which N. I. C. E 430 pushes the Follow button for you on the Cockpit screen automatically (Page 75). This can be turned on for re-enabling both Lock-to-Position and Smart Zoom. 4. 5. 5 Cursor (No. 7) As described earlier (Page 22), if you tap the map somewhere or select one specific item in Find, it will become the selected point on the map, marked with a small red dot and radiating red circles to make it conspicuous. You can use this point as starting point, via point or destination for your route, you can search for a POI near it, mark it with a pin, or save it as a POI. Note: When GPS position is available, the Follow button will appear indicating that you have disabled Lock-to-Position. Tapping the Follow button will re-enable the position lock and move the cursor back to the current GPS position. The same happens when N. I. C. E 430 restores Lock-to-Position automatically on the Cockpit screen, if it is set in Advanced settings (Page 75). 4. 5. 6 Map scale (No. 8) The scale indicator is only available on the Map screen. In 2D map view it represents the scale of the map. In 3D view it is the scale of the nearest part of the map only. 32 You can use it in both 2D and 3D modes to scale the map. Drag and pull it right to zoom in, or left to zoom out. 4. 5. 7 Menu (No. 9) This button opens the Menu with the Find engine, the Quick menu, the Route menu and the exit button that takes you to the Main menu screen. The Menu will be described in detail later: Page 43. 4. 5. 8 Map orientation and Overview (No. 10) You can view the map screens in three different presentation modes. This switch will cycle through them in the following order. The usual map orientation for navigation is Track-up. [. . . ] Selecting North-up, the map remains oriented to have North toward the top. Use the left and right hardware buttons to turn your map in the direction you wish. This will immediately turn off the automatic rotation. A small compass in the top right section of the map screens (Page 33) will always show the current direction of the map. [. . . ]