User manual CLARION RD3

[. . . ] Driving on extremely bumpy roads which cause severe vibration may cause the sound to skip. Even in the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] These may get caught in the internal mechanism and damage the disc. 5 6. BUTTON TERMINOLOGY Note: · Be sure to read this chapter referring to the front diagrams of chapter 2. CONTROLS on page 3 (unfold). 1 DCP Release Button 2 Up and Down ( 3 POWER Button and ) Buttons FNC (Function) Button 4 Eject ( ) Button [ ] ] ] ] ] ], [ ] ], [ ], [ ], [ ] ] ], [ ], [ ] ] ], [ ] ] ], [ ] ], [ ], [ ], [ ], [ ], [ ] ], [ 5 PS (Preset Station Scan) Button [ English [ [ [ [ DISC Up (UP) Button [ DISC Down (DN) Button [ 6 AS (Automatic Station Store) Button [ 7 ISR (Instant Station Recall) Button [ 8 Z-EHCR (z-enhancer) button [ 9 Preset Buttons [ 11 Play/Pause ( ] ], [ ) Button [ 10 TOP (Top Play) Button [ 12 DISP (Display) Button 13 RDM (Random) Button [ 14 RPT (Repeat Play) Button [ 16 BND (Tuning Mode) Button [ 15 SCN (Intro Music Scan) Button [ MAG (Magazine) Button [ 17 A-M (Audio Mode) Button LD (Loudness) Button 18 Left and Right ( and ) Buttons ] : In Radio Mode ] : In CD Mode ] : In CD Changer Mode ] : In MD Changer Mode 6 7. REMOTE CONTROL (RD3 only) Receiver for remote control unit Operating range: 30° in all directions Remote control unit English Signal transmitter Note: · The remote control function is only available on the RD3. The remote control function is not provided with the RDX455D. Inserting the Batteries 1. Turn the remote control unit over, then slide the rear cover in the direction of the arrow. Insert the AA (UM-3/1. 5V) batteries that came with the remote control unit facing in the directions shown in the figure, then close the rear cover. AA (UM-3/1. 5V) Batteries Notes: Using batteries improperly can cause them to explode. Take note of the following points: · When replacing batteries, replace both batteries with new ones. · Do not short-circuit, disassemble or heat batteries. · Do not dispose of batteries into fire or flames. · Dispose of spent batteries properly. Rear cover Rear side 7 Functions of Remote Control Unit Buttons Mode Button ( FUNC ) BAND DISC UP PROG TOP Radio CD CD changer MD changer Turns power on and off. 2) Press and hold the BND button 16 for 2 seconds or longer, then the display will show "MANU, " which means that a manual selection function is on. 3) Press the Left/Right button 18 and select the right station. Seek Tuning 1) Press the BND button 16 , then select FM1, FM2, FM3 or AM. 2) If the "MANU" on the display is on, press and hold the BND button 16 for 2 seconds or longer. When the "MANU" display is off, the Seek Selection function is on. 3) Press the Left/Right button 18 , then when it selects the station in which there is a broadcast, it automatically stops. Preset Memory Function Preset Memory Function can store up to 24 stations: six stations for each of FM1, FM2, FM3 and AM. Note: · When the present memory function is used, all the content of the memory will be erased. Manual memory function 1) Press the BND button 16 , and select the band you want to store in the memory. 2) Press the Left/Right button 18 then select the station you want to store in the memory. 3) Press and hold the Preset button 9 for 2 seconds or longer, then the station will be stored in the memory. Auto store function (Automatic Station Store) 1) Press the BND button 16 , then select the band you want to store in the memory. 2) Press and hold the AS button 6 for 2 seconds or longer, then the station at which the reception is the strongest will be automatically stored in the memory. Area Change Use this function when you are using the car stereo anywhere outside the U. S. Switchable frequency spacing This car stereo is initially set to tune in frequency intervals of 10 kHz for AM and 200 kHz for FM, the standard calibrations in the U. S. When using the unit outside the U. S. , use the following procedure to switch the frequency range. [. . . ] When this button is pressed again, the MD will play from the previous track. Fast-Forward and Fast-Backward Press and hold the Left/Right button 18 . : To fast-forward : To fast-backward * Pressing the Left/Right button for 1 second or longer will move forward or backward 5 times faster than normal play, and pressing it for 3 seconds or longer will do the operation 30 times faster. 14 Scan Play (Intro Music Scan) Press the SCN button 15 , then the display shows "SCN, " then the MD will play the first 10 seconds of each track of the whole disc. Press the SCN button 15 again to disengage the unit from scan play. * A scan play will start from the track following the one currently playing. Disc scan play Press and hold the SCN button 15 for 2 seconds or longer, then the display will show " " and "SCN", and plays the first 10 seconds of all the tracks of all the MDs in the MD changer. Press the SCN button 15 again to disengage the unit from disc play. English * A scan play will start from the track following the one currently playing. Repeat Play Press the RPT button 14 , then the display shows "RPT, " then the track currently playing will be played repeatedly. [. . . ]